ASTM E2001-24 引用标准 ASTM E1316 ASTM E1876 ASTM E2534 适用范围 1.1 本指南描述了使用共振超声光谱法检测金属和非金属零件缺陷的程序。该程序旨在与能够激发和记录表现出声学或超声波振铃的部件内的全身共振状态的仪器一起使用。它用于区分合格零件和含有缺陷的零件,例如与零件密切相关的裂纹、空隙、碎屑、...
ASTM E2001-24 引用标准 ASTM E1316ASTM E1876ASTM E2534 购买 正式版 1.1 本指南描述了使用共振超声光谱法检测金属和非金属零件缺陷的程序。该程序旨在与能够激发和记录表现出声学或超声波振铃的部件内的全身共振状态的仪器一起使用。它用于区分合格零件和含有缺陷的零件,例如与零件密切相关的裂纹、空隙、碎屑、密度...
2001年 ANSI/ASTM E11:2001 线织试验筛规范 本规范涵盖了测试筛的设计和构造要求,该测试筛使用安装在框架中的编织金属丝布作为介质,用于根据指定粒度(见注 1 和注 2)对材料进行分类测试,以及金属丝布,符合 的规格,被指定为测试等级的金属丝布。所有随后提及的金属丝布均指测试级金属丝布。检查测试筛和金属丝...
Published July 2001. Originally published as E 3 – 21 T. Last previous edition E 3 – 95. 2 Annual Book of ASTM Standards, Vol 03.01. Copyright ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, United States. 1 E3 major uses for metallographic examination are in failure ...
1 These practices are under the jurisdiction of ASTM Committee E28 on Mechanical Testing and is the direct responsibility of Subcommittee E28.01 on Calibration of Mechanical Testing Machines and Apparatus. Current edition approved April 10, 2001. Published May 2001. Originally published as E 4 – ...
ASTM 标准 789 95 2001 《【ASTM标准】E 789 - 95 (2001)》由会员分享,可在线阅读,更多相关《【ASTM标准】E 789 - 95 (2001)(18页珍藏版)》请在人人文库网上搜索。 E 789 95 (001)in a is 789; in of of A in of e) an or of a in a a of of It of of a . of to of if It is...
ASTM E1268-2001(R2016) 显微组织带状程度或取向的评定规程 36的 HRC 值分别为 62.0HRC 和 58.0HRC。 A2.2.4 用公式(A2.4),基体含碳量为 0.44%、轻腐蚀带上的含碳量为 0.58%。58HRC 是HRC-%C 两种线性关系的拐点。如果用公式(A2.3)来估算基体含碳量,得到结果为 0.43%C。淬透性试验数据得到钢淬火...
1ASTME28力学试验委员会拥有本试验方法的最终解释权,并由E28.13残余应力测量小组委员会负直接责任。 现行版本于2001年10月10日通过,2001年11月颁布。起初以E837-81颁布。此前最新版本为E837-99。 小洞也不会明显影响试样的使用的地方。 1.2这个标准并不声称指出了所有对安全性的担心,若有的话,也是联系到它的使...
ASTM_E292-2001 Designation: E 292 – 01 Standard Test Methods for Conducting Time-for-Rupture Notch Tension Tests of Materials1 This standard is issued under the xed designation E 292; the number immediately following the designation indicates the year of original adoption or, in the case of ...
材料与试验协会 E 3-2001金相试样的制备方法(中文版).pdf,Designation:E3–01 1 Standard Guide forPreparation of Metallographic Specimens1 ASTM E3-01 金相试样制备标准指南 此标准发行使用固定编号E2014 ;编号后面紧接的数字表示最初设立adoption 的年份,或是,在