当项目规范仅引用ASTM D4417而不是特定方法时,如果在同一项目中使用两种不同的方法,甚至在同一表面上和同一区域内(例如,承包商的质量),则表面轮廓测量的结果可能会有所不同。控制检查员正在使用复制带,而设施所有者的质量保证检查员正在使用深度千分尺。深度千分尺和复制带法均符合ASTM D4417,但测量采集原理却大...
ASTM D4417-21 引用标准 ASME B46.1-2002 ASTM D7127 ASTM E177 ASTM E691 本体 表面轮廓 购买 正式版 1.1 这些测试方法涵盖了在现场、车间和实验室测量喷砂清理表面轮廓的技术描述。这些测试方法未涵盖其他适合实验室使用的技术。 1.2?方法B也可以 术语 死区 deadband 评估长度 evaluation length H H Pd...
当项目规范仅引用ASTM D4417而不是特定方法时,如果在同一项目中使用两种不同的方法,甚至在同一表面上和同一区域内(例如,承包商的质量),则表面轮廓测量的结果可能会有所不同。控制检查员正在使用复制带,而设施所有者的质量保证检查员正在使用深度千分尺。深度千分尺和复制带法均符合ASTM D4417,但测量采集原理却大不相...
当项目规范仅引用ASTM D4417而不是特定方法时,如果在同一项目中使用两种不同的方法,甚至在同一表面上和同一区域内(例如,承包商的质量),则表面轮廓测量的结果可能会有所不同。控制检查员正在使用复制带,而设施所有者的质量保证检查员正在使用深度千分尺。深度千分尺和复制带法均符合ASTM D4417,但测量采集原理却大不相...
中文标准翻译ASTM D4417ASTM D4417:喷射清理后钢板表面粗糙度的现场检测方法 1.总则 1.1本检测方法包括在实验室,现场或制作车间内测量磨料喷射清理后的钢板表面粗糙度的技术性描述.对于适用于实验室的额外检测技术不包括在内. 1.2以SI为单位的数值是与标准相关的,圆括号内的数值仅供参考. 1.3本标准并非适用于所有的...
2.1.2Method B—The depth of profile is measured using a fine pointed probe at a number of locations and the arithmetic mean determined.2.1.3Method C—A composite plastic tape is impressed into the blast cleaned surface forming a reverse image of the profile, and the maximum peak ...
and establish appropriate safety and health practices and deter- mine the applicability of regulatory limitations prior to use. 2. Referenced Documents 2.1 ASTM Standards: 2 D7127 Test Method for Measurement of Surface Roughness of Abrasive Blast Cleaned Metal Surfaces Using a Por- table Stylus ...
The Replica Tape method is a trusted method used by inspectors worldwide for decades to measure surface profile height. Previous studies have shown the method to be highly precise and accurate, but an intricate burnishing technique and requirement to average two different grades of replica tape in...
peak-to-valley distances is determined.3.1.3 Method C—A composite plastic tape is impressed intothe blast cleaned surface forming a reverse image of the prof i le,and the maximum peak to valley distance measured withthickness gage specif i cally designed for use with the replicatape method.4...
1 asimi0001 翻译-20150316 代号: D4417-03 对吹砂清理钢件表面轮廓现场测量的标准试验方法1 本标准以固定代号 D4417 发布; 紧随该代号之后的数字表示最初采纳的年份, 或者在修订的情况下, 表示最近一次修订的年份。 括号内的数字表示最近一次重新批准的年份。 上标艾普斯龙( ) 表示在上一次修订或重新批准后进行...