The issue coming from use Self-Signed or Expired Certificate for switch management Try to connect usingConnect-ArubaSW -SkipCertificateCheck Unable to connect if you useConnect-ArubaSWand getUnable to Connect Check if the HTTPS is enable on the switch PowerArubaSW# show web-management Web Managem...
#enable secret Password:*** Re-Type password:*** 1. 2. 3. 1.3 Web登陆 如果AC启用了web登陆权限,就可以通过: https://<Controller’s IP address> 登陆AC 2. 控制器基础配置 2.1 控制器恢复出厂设置 write erase只删除配置文件 write erase all将删除配置文件、控制器内部数据库及license,将控制器重置...
radio enableservice-template h3c-macauth vlan 1308## 配置AC和Switch相连的接口为Trunk类型,允许Client所在VLAN通过。#interface Ten-GigabitEthernet1/0/26port link-type trunkport trunk permit vlan all#2. 配置Switch# 创建VLAN 1308及其对应的VLAN接口,并为该接口配置IP地址,Client使用该VLAN接入无线网络。
设备上只需要将认证方式修改为EAP,其它配置无需修改,请参考6.3.1 配置Switch。[Device] dot1x authentication-method EAP6.5.2 配置ClearPass服务器上只需要将“服务”中的“身份验证方式”修改为EAP-MD5即可,其它配置无需修改,请参考6.3.2 配置ClearPass。
Re-type Password for enable mode: *** Do you wish to shutdown all the ports (yes|no)? [no]: no Current choices are: System name: Aruba7005 Switch Role: master VLAN 1 interface IP address: 10.0.90.4 VLAN 1 interface subnet mask: 255.255.255.0 IP Default...
(Aruba7200) (config)#enable secretPassword:***Re-Type password:*** 1.3 Web登陆 如果AC启用了web登陆权限,就可以通过: https://<Controller’s IP address> 登陆AC 2. 控制器基础配置 2.1 控制器恢复出厂设置 write erase只删除配置文件 write erase...
Switch should be rebooted now. (Aruba-master) (config) #interface vlan 1 (Aruba-master) (config-subif)#no ip address (Aruba-master) (config-loopinterface fastethernet 1/0 )#(Aruba-master) (config-if)#switchport access vlan 200 (Aruba-master) (config-if) #exit...
Switch Role: master Country code: cn Time Zone: PST-8:0Ports shutdown: no If you accept the changes the switch will restart!Type<ctrl-P> to go back and change answerforany question Do you wish to accept the changes (yes|no)y
配置SwitchC作为DHCP服务器,为用户终端分配IP地址。 [SwitchC]dhcp enable//全局使能DHCP服务 [SwitchC]interface Vlanif 10[SwitchC-Vlanif10]ip address 192.168.10.1 24[SwitchC-Vlanif10]dhcp select interface[SwitchC-Vlanif10]quit[SwitchC]interface Vlanif 20[SwitchC-Vlanif20]ip address 192.168.20.1...
(ArubaS2500-24P) #re? reload Coldstart the switch rename rename a file restore restore file or configuration (ArubaS2500-24P) #reload Do you want to save the configuration(y/n): n Do you really want to restart the system(y/n): y System will now restart!