CLI 模式进入 41 5.5 AP CLI 配置模式 42 5.6 设置AP MASTER 地址 42 5.6 设置AP 的IP 地址 43 5.7 外接天线AP 配置 43 5.8 AP HELP 参数 43 5.9 AP 命令显示信息 44 3 Aruba 命令行配置手册 第1 章 关于命令行配置手册 本章包括以下内容: • 内容范围 • 适用对象 • 相关文档 1.1 内容范围...
25、e connect 1/0 /* 输入控制器上 AP 所连接的端口号,slot 插槽 port 端口 重启 AP,直接拔掉电源,如果使用 poe 则直接重新插拔网线 在启动过程中出现倒计时,立刻按回车,显示如下: User:admin Password:admin Available commands: connect exit soe connect 1/0 Connecting to 1/0 at 9600 baud 8N1 Type...
在ArubaOS 8.x 下,无需登录控制器本地,所有操作均可以通过MM CLI 完成,登录命令提示符: (MM-VA1) [mynode] # 设备名称 当前目录 进入全局配置模式: (MM-VA1) [mynode] #configure terminal Enter Configuration commands, one per line. End with CNTL/Z (MM-VA1) [mynode] (config) # 改变当前...
VBS4We-uWGGkML-8019LD/t-PmQ Plsa.se reload, the switch for the riew service key to take effect. (Aruba200) it 此处会提示你重新启动系统,可以暂时不重启,等基础配置完成后再重启 .配置基本网络信息(包括VLAN、IP地址以及网关) (Aruba200) #configure terminal Enter Configuration commands, one per ...
*使用CLI创立VLAN: (aruba) User:admin Password:*** (aruba)enable Password:*** (aruba)#configureterminal EnterConfigurationcommands,oneperline.EndwithCNTL/Z (aruba)(config)#vlan5 (aruba)(config)#interfacevlan5 (aruba)(config-subif)#exit (aruba)...
What is our primary use case? Aruba switches are primarily used as L2 switches, with some used as L3 switches as well. The ProCurve series is most commonly used, rather than the HEC or 192 series. The switches are also used for IPTV and multicast. ...
12、e-uWGGkML-8919ID/t-Pn!QPlfta.serelsadtheswitchfat:tkerieurkeytotakeeff(Aniba200)#此处会提示你重新启动系统,可以暂时不重启,等基础配置完成后再重启3 .配置基本网络信息(包括VLAN、IP地址以及网关)(Aruba200)#configureterminalEnterConfigurationcommands,oneperline.EndwithCNTL/Z(Aruba200)(config)#contro...
Aruba Instant 8.6.0.4 AOS-212652 An Instant AP inherits the gateway IP of the layer 2 switch in the event of a switch outage and causes an IP address conflict when the switch is back online. The fix ensures that the AP does not inherit the gateway IP of the layer 2 switch in ...
In most cases, the Instant AP will display the error message Warning: CLI Module is running in a degraded state. Some commands will not function 1. When the Instant AP cannot be a master Instant AP because it has no IP address, and does not have an uplink connection. 2. When the ...
To disable the LCD screen, enter the Enable mode and use the following CLI commands: (host) #configure terminal (host) (config) #lcd-menu (host) (lcd-menu) #disable menu To disable only the Maintenance menu or one of its sub-menus, enter the Enable mode and use the following CLI ...