硬件要求:了解LCD接口所需的基本硬件组件。连接LCD硬件:将LCD连接到Arduino板的分步指南。编写第一个LCD代码:编写并运行第一个代码以在LCD上显示文本。文本动画:学习如何在LCD屏幕上左右移动文本。创建自定义字符:探索如何在LCD上设计和显示自定义字符。谁是Arduino爱好者的这门课程:非常适合那些想用视觉显示来增强Ardui...
// (note: line 1 is the second row, since counting begins with 0):lcd.setCursor(0, 1);//...
//tft.initR(INITR_BLACKTAB); // Init ST7735S chip, black tab // OR use this initializer if using a 1.8" TFT screen with offset such as WaveShare: // tft.initR(INITR_GREENTAB); // Init ST7735S chip, green tab // OR use this initializer (uncomment) if using a 1.44" TFT: t...
TFT LCD 与 Arduino 连接: 2.4英寸TFT LCD屏幕是一个完美的Arduino Shield。您可以直接将LCD屏幕推到Arduino Uno的顶部,它将与引脚完美匹配并滑入。但是,出于安全考虑,用小绝缘胶带覆盖Arduino UNO的编程端子,以防终端与TFT LCD屏幕接触。在UNO上组装的LCD如下所示。 为TFT LCD 编程您的 Arduino: 我们正在使用SPF...
lcd. begin(16, 2); pinMode(TrigPin, OUTPUT); pinMode(EchoPin, INPUT) ; } voidloop() { digitalWrite(TrigPin, LOW); delayMicroseconds(2); digitalWrite(TrigPin, HIGH); delayMicroseconds(10); digitalWrite (TrigPin, LOW); inttimer=-500; ...
(0, 32); // Outputs canvas to OLED with an offset (x pixels, y pixels) engine.canvas.clear(); for (int i = 0; i < 8; i++) { if (data[i] > 31) engine.canvas.drawVLine(i * 4, 31 - (data[i] - 31), 31); // Draw to canvas data for upper-leftest sector (FFT ...
I2C/TWI LCD2004模块来自DFRobot相当酷的一款I2C接口的LCD显示器,采用I2C的通讯接口驱动。LCD2004能够为您的MCU控制器节省大量的数字引脚,也为你的Arduino控制器系统的显示开发节省大量的软件开发时间成本,只要2根信号线就可以搞定全部链接。这款LCD显示器拥有4x20字节的STN白色字符显示及炫酷的蓝色背光灯。平整的设计能...
用Tinkercad学arduino之 LCD温度显示报警器 项目地址:https://www.tinkercad.com/things/9Yv09OZnrXy-temperature-sensor-with-display //CREATED BY GIOVANNI, LUCAS B, LUCAS F & THIAGO.//WHEN THE TEMPERATURE IS HIGHER THAN 35ºC IT PLAYS ANOTHER SOUND FREQUENCY.//Include the library code.#...
1.首先我们需要包含使用I2C通信功能的Wire库和使用LCD功能的LCD库。还为 16x2 LCD 定义 LCD 引脚。在此处了解有关将 LCD 与 Arduino 连接的更多信息。 #include #include LiquidCrystal lcd(2, 7, 8, 9, 10, 11); 2. 在 void setup() 我们以波特率 9600 开始串行通信。
char array2[]="hello, world! "; //the string to print on the LCD int tim = 500; //the value of delay time // initialize the library with the numbers of the interface pins LiquidCrystal_I2C lcd(0x27,16,2); // set the LCD address to 0x27 0x3F for a 16 chars and 2 line dis...