第44期《Arduino入门》传感器 01:红外线传感器 IR Sensor#硬声创作季 电子学习 190 11 Arduino创意项目十九:指纹门锁。收集有趣有味有创意的项目与大家分享 产品为王的时代来了 2.8w 641 用arduino控制继电器 纸箱里的猫咪 7458 281 做一个激光围栏,终于实现了小时候的新奇想法 SR Electric 4441 191 #跟着
Kumar, "Arduino based wireless intrusion detectionusing IR sensor and GSM," Int. J. Comput. Sci. Mobile Comput., vol. 2,no. 5, pp. 417-424, May 2013.Prakash Kumar, Pradeep Kumar. Arduino Based Wireless Intrusion Detection Using IR Sensor and GSM. International Journal of Computer Science...
硬声是电子发烧友旗下广受电子工程师喜爱的短视频平台,推荐第44期《Arduino入门》传感器 01:红外线传感器 IR Sensor视频给您,在硬声你可以学习知识技能、随时展示自己的作品和产品、分享自己的经验或方案、与同行畅快交流,无论你是学生、工程师、原厂、方案商、代理商、
本项目采用Arduino开发板、火焰传感器(Flame Sensor)、蜂鸣器,构建了一个简单的火感检测器系统。一旦探测到火焰出现,蜂鸣器就发出警报,可用作火警车、IoT火灾警报器、智能联网火灾报警器的原型。 IR火焰传感器 IR火焰传感器主要由双电压比较器IC、IR传感器和一个电位器组成,4个引脚功能如下: A0:模拟输出引脚 G:接地引...
your electronic modules. The high-quality polymer CD-ROM reading speed ensures that the sensor maintains its performance even under high-speed operations. With a temperature range of 105℃ and a low 3分贝 bandwidth, these sensors are built to withstand the rigors of industrial and hobbyist ...
2)将 Arduino Sensor Shield V5.0 放在 Arduino 板的顶部,注意将相应的引脚耦合在一起。 3)用螺钉将 2个 IR 传感器安装在机箱上。使用底盘上的定向支撑,以使传感器定向为 30°。这一步很重要,因为红外传感器用于检查机器人左右两侧的障碍物。 4)将 Micro 伺服 SG90 安装在机箱方孔上。使用 2 个螺丝固定。
IR Thermometer Sensor-MLX90614红外温度传感器模块是一款基于MLX90614红外测温传感器的温度测量模块。 MLX90614 是一款无接触式的红外线温度感应芯片,它在同一TO-39封装内整合了红外热电堆感应器与一款定制的信号调节芯片。 MLX90614在信号调节芯片中使用了先进的低噪音放大器,一枚17-bit ADC以及功能强大的DSP元件, 从而...
IRReceiver pinoutsAdafruit IR Sensor tutorialReceiving IR codesIn your program you check for a completely received IR frame with: if (IrReceiver.decode()) {} This also decodes the received data. After successful decoding, the IR data is contained in the IRData structure, available as Ir...
Optical Proximity Sensor and Ambient Light Sensor with IrLED RPR-0521RS RPR-0521RS是一款集成了光学接近传感器、数字环境光传感器IC和红外LED的模块。该模块通过反射红外LED光线检测人或其他物体的接近,同时检测从暗环境到直射阳光的广泛光照范围。它支持I2C总线接口,具有低电流消耗功能,并提供了两个ALS输出,分别...
/IR) sensor on the APDS-9930 @param[in] interrupts true to enable hardware interrupt on high or low light @return True if sensor enabled correctly. False on error. */ bool APDS9930::enableLightSensor(bool interrupts) { /* Set default gain, interrupts, enable power, and enable sensor...