The MindPlus Coding Kit for Arduino is an ideal educational tool for kids to start their coding journey. Featuring an Arduino Uno R3 mainboard, sensor expansion board V7, and 18 essential sensors and actuators,
Arduino® UNO R3 Product Reference Manual SKU: A000066 Description The Arduino UNO R3 is the perfect board to get familiar with electronics and coding. This versatile microcontroller is equipped with the well-known ATmega328P and the ATMega 16U2 Processor. This board will give you a great ...
The Arduino UNO R3 is the perfect board to get familiar with electronics and coding. This versatile microcontroller is equipped with the well-known ATmega328P and the ATMega 16U2 Processor. This board will give you a great first experience within the world of Arduino. ...
SmartKIT-ESP是一款兼容ArduinoUNOR3引脚的STM32开发板,为了测试以及后续移植程序的方便,我搜集了一些STM32F103C8T6 LQFP48的资料,将SmartKIT-ESP的各个引脚标注了一下,与ArduinoUNOR3的引脚进行了简单的对比,现发出来与大家分享一下。 1、STM32F103C8T6 LQFP48 引脚图 2、STM32F103C8 ...
ArduinoUno R3 2.8英寸TFT触摸液晶屏 锂电充电电池600mAh 3.7v(最大物理尺寸30mm x 50mm x 6mm) TP4056锂电池充电器板Micro USB 连接线 使用最小160mm x 70mm x 30mm的3D打印机 3.3K 1/8W电阻 拨动开关 实物连接 2. 打印3D外壳 使用白色PLA打印3D盒子,触摸屏手写笔插入Arduino PCB下的空腔中,可以用手指...
The Arduino UNO is the best board to get started with electronics and coding. The Arduino Uno Rev 3 is a microcontroller board based on the ATmega328, an 8-bit microcontroller with 32KB of Flash memory and 2KB of RAM, which is the most used and documented board of the whole Arduino fam...
MindPlus Coding Kit for Arduino is a set of tools for programming learning. As its compatibility for Mind+, a graphical coding software for starters, and Arduino IDE, this kit is well applicable to students from the lower grade to the higher grade. It comes with an Arduino Uno R3 mainboar...
文章目录 准备材料 安装Arduino驱动 代码编辑器 代码编辑 硬件链接 不用写一个代码完成RC522读卡操作 准备材料 ① 硬件 Arduino-uno-r3 开发板一块 开发板USB线一条 RFID-RC522读卡器一块 杜邦线(公对公)7跟 电脑一台(能用的) 卡片若干(一张就够用了,一般买一块RC522板会赠送两个) ② 软件 Arduino驱动 ...
Arduino Uno (R3) Uno是新手入门Arduino时的绝佳选择。 它有你入门所需要的一切。 它有14个数字输入/输出引脚(其中6个可用作PWM输出),6个模拟输入,USB连接,电源插孔,复位按钮等。 它包含支持微控制器所需的一切; 只需使用USB电缆将其连接到计算机,或使用交流 – 直流适配器或电池为其供电即可开始使用。
系统以Aruidno UNO R3 为核心, 使用DHT22 传感器采集温湿度, BH1750 传感器采集光照强度, BMP180 传感器采集大气压强, DS3231 获取时间信息, MQ-2 传感器采集烟雾浓度, 以及雨量和土壤湿度传感器采集相关信息, 并使用两个继电器作为控制传感器电源开关, 以达到节能的目的。设计框架如图1 所示。