void setup() { // initialize the LED pin as an output: pinMode(ledPin, OUTPUT); // initialize the pushbutton pin as an input: pinMode(buttonPin, INPUT); // initialize the cloudBit trigger pin as an output: pinMode(trig_out, OUTPUT); } void loop() { // readthe state of the ...
在本教程中,我们将使用 Arduino UNO、OLED Lcd、MQ-3 酒精气体传感器模块和 Visuino 在 Lcd 上显示酒精含量并设置检测限值。 第1 步:您需要什么 1 / 4 Arduino UNO 或任何其他 Arduino MQ-3 酒精气体传感器模块 OLED液晶屏 面包板 跳线 Visuino 程序:下载Visuino 第2 步:电路 将Arduino UNO 的 GND 连接到...
Arduino UNO开发板为我们提供了了 A0~A5 6个ADC引脚。本期教程只用到一个引脚进行演示。 示意图: 二、实现 1.介绍相关函数 读取模拟输入函数 analogRead(pin) 参数:pin-指要读取的模拟输入引脚的名称 需要用到的三个串口输入输出函数 Serial.begin(baudrate): 这个函数用来初始化串口,设置波特率,即每秒传输的...
Each of the 14 digital pins on the Uno can be used as an input or output, using pinMode(),digitalWrite(), and digitalRead() functions. They operate at 5 volts. Each pin can provide or receive 20 mA as recommended operating condition and has an internal pull-up resistor (disconnected by...
Arduino睡眠模式也称为Arduino省电模式(Power Save mode)或Arduino待机模式(Standby Mode)。Arduino睡眠模式允许用户停止或关闭微控制器中未使用的模块,从而显着降低功耗。 Arduino UNO、Arduino Nano和Pro-mini配备了ATmega328P,它有一个欠压检测器(BOD),用于监控睡眠模式时的电源电压。
由于arduino UNO的引脚太少,所以需要把电源还有GND引出来,所以需要与面包板配合使用。Arduino上的5V接到面包板正极,arduino上的GND接到面包板上的负极。 (2)Arduino与L298N电机驱动模块接线说明 I1 I2 I3 I4:电机控制输入端,直接接单片机的IO口 OUT1 OUT2 OUT3 OUT4:...
以“while”开头的那行代码确保在USB连接的另一端有东西可以让Arduino在开始发送消息之前与之对话。否则,消息可能被发送,但不会显示。这一行实际上只有在你使用Arduino Leonardo时才有必要,因为当你打开串行监视器时Arduino Uno会自动重启Arduino板,而Leonardo则不会发生这种情况。
连接电源与电机,通过Arduino uno提供的高低电平从而控制电机的转动。中间的三个蓝色接口从左到右依次是12V输入,GND(接地),以及5V输入(值得注意的是,这里的5V输入不能当做电源驱动电机运行,而是可作为电源接入Arduino,为Arduino提供电源)。左右两边的各两个蓝色的接线柱是OUT1~4,分别连接左右电机,输出电流。中间右侧的...
Arduino Uno上的"pin change"中断是通过PCINT(Pin Change Interrupt)来实现的。PCINT是Arduino Uno上的一个特殊功能,它允许在特定引脚状态变化时触发中断。 在Arduino Uno上,有三个可用的PCINT引脚组,分别是PCINT0、PCINT1和PCINT2。每个组包含多个引脚,可以通过设置相应的寄存器来启用或禁用中断。 具体来说...
constint keyPin = 2; //接入中断引脚 Adafruit_NeoPixel strip = Adafruit_NeoPixel(num, PIN, NEO_GRB + NEO_KHZ800);int modu = ;voidsetup(){ // This is for Trinket 5V 16MHz, you can remove these three lines if you are not using a Trinket #ifdefined (__AVR_ATtiny85__)if(F_CPU...