AREF. Reference voltage for the analog inputs. Used with analogReference(). Reset. Bring this line LOW to reset the microcontroller. Typically used to add a reset button to shields which block the one on the bo
Operating Voltage 5V/3.3V Power Consumption TBD Product Weight(Package containing) 44g(have touch screen),55g(have no touch screen) Interface Definition Number Pin Label Pin Description 1 LCD_RST LCD bus reset signal, low level reset 2 LCD_CS LCD bus chip select signal, low level en...
Arduino Uno是一款基于ATmega328的微控制器板。它有14个数字输入/输出引脚(其中6个可用作PWM输出)、6个模拟输入、1个16 MHz陶瓷谐振器、1个USB连接、1个电源插座、1个ICSP头和1个复位按钮。它包含了支持微控制器所需的一切;只需通过USB电缆将其连至计算机或者通过AC-DC适配器或电池为其供电即可开始。A000066查...
Each of the 14 digital pins on the Uno can be used as an input or output, using pinMode(), digitalWrite(), and digitalRead() functions. They operate at 5 volts. Each pin can provide or receive 20 mA as recommended operating condition and has an internal pull-up resistor (disconnected ...
arduino leonnardo和uno 这两个板子的CPU不一样,Leonnardo用的是ATmega32u4,UNO用的是ATmega328。最大的区别是在USB上面,Leonnardo的USB接口是CPU原生的,而UNO是通过ATmega16u2转的。这导致它们在使用上有一点微小的区别。Leonnardo可以模拟成USB的键盘,鼠标,而UNO不行。如果使用串口功能,由于Leonardo是CPU直接连接USB,...
The UNO R4 Minima board's operating voltage is 5 V, making it hardware compatible with UNO form factor accessories with the same operating voltage. Shields designed for previous UNO revisions are therefore safe to use with this board but are not guaranteed to be software compatible due to the ...
完全兼容Arduino UNO R3接口 摇杆X\Y轴输出为两个电位器,可以通过AD转换读出扭动角度 向下按摇杆,可以触发一路轻触开关,为数字输出 四路独立按键,数字输出,方便使用 板上标注有各个模块的端口配置,方便调试 预留了其他没有占用的端口,方便后期扩展 通过该扩展板可以制作一个遥控手柄,结合XBee模块可实现无线控制 ...
Arduino Uno ATmega328具有32 KB闪存(其中0.5 KB被启动加载器占用)。它还具有2KB SRAM和1KB EEPROM(可以利用EEPROM库读取和写入)。 Arduino Uno可通过USB连接或者外部电源供电。外部(非USB)电源可以是AC-DC适配器,也可以是电池。通过将2.1mm中心正极插头插入电路板的电源插座即可连接适配器。电池的引线可插入电源连接...
Operating voltage:5VInput voltage:6-24VClock speed:48MHzProgramming port: USB-CDigital pins:14PWM:6ADC:6DAC:1(12bit)SPI:1I2C:1CAN:1 Documents Arduino UNO R4 Minima Datasheet: https://github.com/May-DFRobot/DFRobot/blob/master/UNO%20R4%20Minima-datasheet.pdf Arduino UNO R4 WiFi Data...
PWM引脚在引脚编号旁边由波浪号(〜)表示,例如在Arduino Uno的数字引脚图像中。 最后,将Arduino数字输出引脚连接到驱动程序模块。在我们的示例中,我们有两个直流电动机,因此数字引脚D9,D8,D7和D6将分别连接到引脚IN1,IN2,IN3和IN4。然后将D10连接到模块插针7(先卸下跳线),然后将D5连接到模块插针12(同样要...