1 × Push Button Module 1 × SSD1306 I2C OLED Display 128x64 1 × SSD1306 I2C OLED Display 128x32 1 × Breadboard 1 × Jumper Wires 1 × Recommended: Screw Terminal Block Shield for Arduino Uno 1 × Recommended: Breadboard Shield for Arduino Uno 1 × Recommended: Enclosure for...
双击图标打开 IDE 并用 USB 将 Arduino 连接到计算机后,您需要检查工具菜单,查看 Arduino Uno 是否作为主板列出,以及它连接到哪个端口。在菜单中进入工具/板,并检查板说“Arduino/genu ino Uno”;如果没有,从下拉菜单中选择 Uno。 港口 您将通过其中一个 USB 端口将 Arduino 连接到计算机;这些端口有一个编号,在...
第一页还有一个滑块来控制另一个 LED 的亮度; 第二页在文本标签中显示当前温度,在进度条中显示当前湿度; 此页面有一个更新按钮,用于更新读数。所需零件以下是此项目所需的部分:2.8 英寸 Nextion 显示屏(或 3.2 英寸 Nextion 显示屏) MicroSD卡 Arduino UNO 2个 LED DHT11温湿度传感器 2x 220 欧姆电阻 4.7...
Some models of the Uno have additional I2C connectors as well. The following diagram illustrates how to hook up an Arduino Uno to an LCD display with the I2C bus adapter: Note how much easier it is to use the I2C connection, which does not consume any of the Arduino Unos 14 digital I...
Arduino Based POV Display Stick - JolliPOV Stick: Basic Arduino boards such as the Arduino Uno, Arduino Nano, and Arduino mini boards are very popular with entry-level electronics hobbyists working on electronics projects. There are a lot of interesting
在GPIO 章节中,我们构建了一个带 LED 的小电路。然而,Arduino 有一个内置在电路板上的 LED 供我们使用,所以我们还不需要打开试验板。LED 与 UNO 上的 13 号插脚相连;其他版本可能会有所不同。从编程菜单中打开 Arduino IDE。 验证板已连接并被检测到。 在Arduino IDE 菜单上,转到工具并将鼠标悬停在电路板...
// Arduino pin connected to relay's pinezButtonbutton(BUTTON_PIN);// create ezButton object that attach to pin 7;voidsetup() {Serial.begin(9600);// initialize serialpinMode(RELAY_PIN,OUTPUT);// set arduino pin to output modebutton.setDebounceTime(50);// set debounce time to 50 ...
Shivakumar Jogur2017년 10월 7일 0 링크 번역 댓글:Nicolas Schmit2017년 10월 11일 Requirement: If I press push button LED should toggle and it should switch off immediately after releasing push button. 답변 (0개) ...
Nextion Display with Arduino – Getting Started This post is an introduction to the Nextion display with the Arduino. We’re going to show you how to configure the display for the first time, download the needed resources, and how to integrate it with the Arduino UNO board. We’ll also ...
一,离开楼主两年的UNO终于要再次回到楼主身边了。二,以后会分享下Arduino跟Microsof C++通信经验。因为处理图像,比如照片、视频并不是matlab的强项,速度较慢。开源的OpenCV是个不错的选择,网上资料也很全。 春泥蛋炒饭 赫赫有名 13 沙发,好贴果断加精! 飘雪才子 闻名一方 11 楼主很效率么 哈哈 我刚说就发出来...