2.Arduino代码 #include <Wire.h>#include "MAX30105.h"#include "spo2_algorithm.h"MAX30105 particleSensor;#define MAX_BRIGHTNESS 255#if defined(__AVR_ATmega328P__) || defined(__AVR_ATmega168__)//Arduino Uno doesn't have enough SRAM to store 100 samples of IR led data and red led da...
Serial.print("Infrared Switch Status:"); Serial.println(digitalRead(InfraredSensorPin), BIN); delay(1000); } 串口输出结果 当传感器没有监测到目标的时候,Uno控制板上13脚的LED灯熄灭,并且串口监视器会接收到数字“1”;当传感器监测到目标的时候,LED灯会被点亮,并且串口监视器会接收到数字“0”。如果需要...
The IR sensor module also consists of other components such as anIR emitter LEDwhich emits the infrared light, anIR receiver LEDwhich receives the light after the collision with any object, apower LEDwhich turns on when this sensor is powered up,distance adjuster, through this, the user can ea...
const int InfraredSensorPin = 4;//Connect the signal pin to the digital pin 4 const int LedDisp = 13; void setup() { Serial.begin(57600); Serial.println("Start!"); pinMode(InfraredSensorPin,INPUT); pinMode(LedDisp,OUTPUT); digitalWrite(LedDisp,LOW); } void loop() { if(digitalRead...
实验一百四十三:ML8511紫外线传感器模块 模拟量输出UV Sensor Breakou 接线 ML8511 arduino uno VCC---VCC OUT---A0 GND---GND 实验之一:串口显示ML8511紫外线传感器数值 */ intReadUVintensityPin = A0;//Output from the sensor voidsetup() { pinMode(Read...
实验一百四十三:ML8511紫外线传感器模块 模拟量输出UV Sensor Breakou 接线 ML8511 arduino uno VCC---VCC OUT---A0 GND---GND 实验之一:串口显示ML8511紫外线传感器数值 */ int ReadUVintensityPin = A0; //Output from the sensor void setup() { pinMode...
Arduino Uno控制器负责读取LabVIEW上位机发来的距离测量命令,并通过GP2D12红外传感器获取距离数据,通过串口发送回上位机LabVIEW软件。Arduino Uno控制器的程序代码如下所示: 代码语言:javascript 代码运行次数:0 运行 AI代码解释 #define Infrared_COMMAND0x10//采集命令字byte comdata[3]={0};//定义数组数据,存放串口...
- Arduino Uno 开发板 x1 - 面包板 x1 - UBS接线 x1 - 装有Arduino IDE的电脑 x1 电路图 电路图 接线步骤 第一步,把避障传感器插在面包板上。 第二步,用一根面包线连接传感器的OUT引脚到开发板上的数字引脚7。 第三步,用一根面包线连接传感器的GND引脚到面包板负极。
实验接线:S12SD紫外线模块OUT接Uno的A0 */ voidsetup() { Serial.begin(9600); } voidloop() { floatsensorVoltage; floatsensorValue; sensorValue = analogRead(A0); sensorVoltage = sensorValue/1024*3.3; Serial.print("传感器读数 = "); Serial.print(sensorValue); ...
不同于传统的红外接近检测传感器(infrared proximity sensors),VL53L0X输出的是精确到毫米的测距结果,目标物体的颜色和反射光不会影响测距结果。快速响应的FlightSenseTM技术,因被大品牌智能手机摄像头激光辅助自动对焦所采用而享誉业界,能够区分目标物体的横向或纵向移动。传感器内部完成测距计算,通过I2C总线接口输出数据,因...