https://e2e.ti.com/support/amplifiers-group/amplifiers/f/amplifiers-forum/665127/ina219-no-output-when-load-is-connected-using-arduino-uno 部件号:INA219 hii; 我正在使用INA219模块测试LED项目的电压和电流感应。 唯一的问题是Arduino IDE的串行监视器上不显示任何电压或电流(即0.00V和0.0...
Arduino Unois a microcontroller board based on the ATmega328P (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz quartz crystal, a USB connection, a power jack, an ICSP header and a reset button. It contains everyth...
intMODE_BUTTON =6;41intmode =0;//0: 关机; 1: 长亮; 2: blink42boolean lastButton_mode =LOW;43boolean currentButton_mode =LOW;4445voidsetup()46{47pinMode(BLED, OUTPUT);48pinMode(GLED, OUTPUT);49pinMode(RLED, OUTPUT);50pinMode(R_BUTTON, INPUT);51pinMode(G_BUTTON, INPUT);52pinMo...
将多个LED以“共阳”接法连接起来,再将多组“共阳”层叠起来,每层负极相连,组成一座灯塔,电路原理类似于LED点阵,各层的正极与负极分别连接Arduino UNO的I/O 端口,见图1: 图中R1——R5为限流电阻,Arduino UNO 各端口可以输出20mA 电流,为确保LED的使用寿命,中间串联100——330欧姆的电阻,五个LED的正极端与Ardui...
Arduino UNO只有两个外部中断插脚。但是如果您需要超过2个中断呢?幸运的是, Arduino UNO支持所有插脚上的“引脚改变”中断。 引脚改变类似于外部中断。不同之处在于,一个中断是为8个相关引脚中的任何一个上的状态变化生成的。这些处理起来有点复杂,因为您必须跟踪所有8个引脚的最后已知状态,以确定是哪8个引脚导致...
大多数Arduino板都会自带一个LED灯,不过这个灯可能会根据Arduino板的型号而连接在不同的接口上。就我们所示范的Arduino Uno,来说,它的LED灯是连接到D13接口的。 每个Arduino板都会自带一个常量,LED_BUILTIN,来储存这个接口的数值。 不过,我们也可以在Arduino板上外接一个LED灯,就像下图所示 ...
Arduino Uno is a microcontroller board based on the ATmega328P (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator (CSTCE16M0V53-R0), a USB connection, a power jack, an ICSP header and a reset bu...
Arduino Uno microcontroller development kit. A Brief Introduction To Arduino An Arduino is a development platform used by many development kits that operate using Atmel-based microcontrollers. Arduino doesn’t refer to a particular microcontroller, but rather a platform for microcontrollers. ...
噢,原来在注释里有说明,多数开发板都有可控制的LED小灯,在UNO、MEGA和ZERO 这三个开发板上的led灯输出引脚为13,MKR1000上的可控LED小灯连接的引脚为6,在Arduino里面不管开发板可控制这颗集成的LED的引脚号是多少,在程序里面都可以用关键词:LED_BUILTIN来代替,在Arduino设置好开发板型号以后,LED_BUILTIN就代表了...
B)OUTPUTC)INPUT_PULLUPD)INPUT_PULLDOWN 相关知识点: 试题来源: 解析 A,B,C Arduino UNO/Nano的数字引脚工作模式包括INPUT(输入)、OUTPUT(输出)和INPUT_PULLUP(上拉输入)。INPUT_PULLDOWN(下拉输入)并非标准支持的选项,因此正确答案为A、B、C。题目选项包含正确选项,且问题完整,故给出答案。