int buttonUpState = digitalRead(pullUp); int buttonDownState = digitalRead(pullDown); // make a message that will be sent to the serial line String message = “Pull Up: ” + String(buttonUpState); message = message + “。 Pull Down: ” + String(buttonDownState); // send the message...
5. 面包板(外接时将LED_BUILTIN改为实际引脚数) 6. 数字信号输入 1)按键开关(Push Button):当引脚设置为输入(INPUT)模式时,可以识别两种状态:HIGH(高电平)LOW(低电平),引脚为高阻抗状态(100MΩ),此时引脚可用于读取传感器信号或开关信号。 2)按键开关相连不同侧,同侧不相连;上拉电阻:10kΩ;引脚悬空(Float...
pinMode(LED_BUILTIN, OUTPUT) //定义输出引脚 pinMode(LED_BUILTIN, INPUT) //定义输入引脚 1. 2. 引脚高低电平设定 digitalWrite(LED_BUILTIN, LOW); //高低电平设置 1. 引脚高低电平读取 digtialRead(pushButton); //引脚电平读取 1. 延时函数 delay(1000); //延时1000ms 1. 串口波特率设置 Serial.b...
[0] <= 0xe0)){Serial.write(pev->data[0] | pev->channel);Serial.write(&pev->data[1], pev->size-1);}else{Serial.write(pev->data, pev->size);}}void setup() {pinMode(buttonPin, INPUT_PULLUP); // use builtinpullup resistor with push buttonpinMode(ledPin,OUTPUT);digitalWrite(...
Arduino Uno ATmega328具有32 KB闪存(其中0.5 KB被启动加载器占用)。它还具有2KB SRAM和1KB EEPROM(可以利用EEPROM库读取和写入)。 Arduino Uno可通过USB连接或者外部电源供电。外部(非USB)电源可以是AC-DC适配器,也可以是电池。通过将2.1mm中心正极插头插入电路板的电源插座即可连接适配器。电池的引线可插入电源连接...
https://www.arduino.cc/en/Tutorial/BuiltInExamples/Graph */ (3)设置函数 void setup() { // initialize the serial communication: 初始化串口通信 Serial.begin(9600); } (4)循环函数 void loop() { // send the value of analog input 0: ...
Arduino Uno图1-1Raspberry Pi 3 B+Raspberry Pi 是一种单板计算机,大约有信用卡大小。尽管它的尺寸很小,但它是一个非常强大的设备。Pi 运行一个 Linux 版本,该版本被定制为在驱动它的 ARM 处理器上工作。这将许多功能放入一个小设备中,该设备很容易嵌入到像机器人这样的东西中。但是,尽管它是一台伟大的...
On the UNO, MEGA and ZERO it is attached to digital pin 13, on MKR1000 on pin 6. LED_BUILTIN is set to the correct LED pin independent of which board is used. If you want to know what pin the on-board LED is connected to on your Arduino model, check the Technical Specs of ...
回顾:用arduino电量led首先需要pinmode函数,pinmode(LED_BUILTIN,OUTPUT),为其配上小电源;接下来需要开关,则用digitalwrite函数,digitalwrite(LED_BUILTIN,HIGH)HIGH相当于开关闭合。 1-10 数字输出1 - 学用LED P11 - 01:27 LED=Light Emitting Diode
#define BUTTON_PIN 12 // 按键开关 --- Arduino 引脚12 #define STATUS_PIN LED_BUILTIN // 状态显示LED --- 开发板内置LED IRrecv irrecv(RECV_PIN); // 红外遥控接收器对象 IRsend irsend; // 红外遥控发射对象 decode_results results; // 储存接收到的红外遥控信息 ...