爱给网提供海量的爱给模型库资源素材免费下载, 本次作品为sw,stl 格式的Arduino Uno项目盒(Arduino Uno Project Box), 本站编号105241171, 该爱给模型库素材大小为353m, 更多精彩爱给模型库素材,尽在爱给网。 浏览本次作品的您可能还对 3D模型CAD打印 感兴趣。 找到更多"3d/模型库/
使用3D打印机制作一个面包板底座,将底部抬高28mm,使反射式光电传感器处于接触盖子背面的高度。请使用分发文件BreadboadHolder.stl。如果您正好有一个高度合适的盒子,也可以用它来代替。 将面包板嵌入支架中,并用双面胶将支架和Arduino UNO固定在盒子上。 步骤6:粘贴标记 制作标记用于反射式光电传感器的读取。请在不干...
您需要选择用于输入的加速度计、Arduino Uno控制器、用于电源的电池和用于输出的压电扬声器。单击生成并将电路放在一起后,您可以使用STL文件3D打印宠物的身体。在你知道之前,你会有一个惊人的34five Arduino宠物,你可以出去散步,你会惊讶于你已经做了多少。完整的教程是在Hackster.io:https://www.hackster.io/circuit...
您需要选择用于输入的加速度计、Arduino Uno控制器、用于电源的电池和用于输出的压电扬声器。单击生成并将电路放在一起后,您可以使用STL文件3D打印宠物的身体。在你知道之前,你会有一个惊人的34five Arduino宠物,你可以出去散步,你会惊讶于你已经做了多少。完整的教程是在Hackster.io:https://www.hackster.io/circuit...
3d溜溜网(3d66)为您提供Arduino-Uno-R3、max6675模块和1602-LCD的外壳CAD图纸下载,文件格式:step,stl,文件大小:1.2MB,软件版本:通用格式,素材维度:3D,下载即用。
Arduino Uno R3电路板外壳,会使用到4个小钉进行固定。 模型文件文件名下载次数文件大小操作 fearduino_uno_r3_base.skp 体积0 cm3 最后更新:2016-09-05 11:33:05 5 112kb 下载 biarduino-uno-r3-base.stl 体积0 cm3 最后更新:2017-05-30 14:15:19 9 106kb 下载 点击查看文件完整清单...
*附件:BoxBottom.7z 第2 步:切割和塑造主垫 1、标记垫子:使用尺子和钢笔勾勒出您需要切割的区域。每个 Pattern 都应与三个 pattern(DrumPatternBig.stl、DrumPatternMiddle.stl、DrumPatternSmall.stl)之一的直径匹配。您可以使用图片上显示的布局或自行安排。
This motor is controlled by an Arduino Uno microprocessor using an EasyDriver V4.4 motor controller. Since the motor shaft is eccentric due to the gearbox it contains, to move the threaded rod, it uses a 1:1 motor and rod gear. Unlike commercial microinjectors, the part where the micro...
Under Tools > Board, make sure to select "Generic ESP8266 Module." Mine defaults to "Arduino Uno" without actively selecting the right board. Install the drivers from the OfferZen Prep page. Make sure to give the drivers the correct permissions in the Security & Privacy area in System Prefe...
Not sure what else to look at. I happen to have an UNO board so I might try to see if for some reason that works (though I guess I'll have to be careful with the code and pin compatibility). Otherwise I might just buy another nano shield. ...