1.连线 我使用的是Arduino(UNO)开发板和LCD1602带拓展板I2C。具体连线比较简单。 GND --- 地线 VCC --- 电源5V SDA --- I2C 数据线 SCL --- I2C 时钟线 2.安装库 arduinoIDE里面有专门为lcd1602编写的库,打开项目->加载库->搜索LiquidCrystal_I2C 3.查找串口地址 首先需要知道LCD的串口地址,之后会用到 ...
I2C和SPI是两种非常流行的串行接口总线。本教程将介绍使用I2C连接Arduino和LCD驱动模块,但是LCD驱动模块也可以连接SPI接口。您可以通过跳接驱动模块上的焊接跳线(图2:LCD驱动模块上的焊接跳线)来设置I2C地址(A0、A1、A2)或使能SPI(SPI使能)。本教程中使用I2C的唯一电路是LCD驱动模块,所以我们不需要更改当前配置。这意...
LCD 显示器 I2C 20X4(如果您使用不同的 LCD,请确保您在 Visuino 组件中指定了正确的列和行) 跳线 Arduino UNO 或任何其他板 Visuino 软件:在此处下载第2 步:电路将LCD 显示引脚 VCC 连接到 Arduino 引脚 5V 将LCD 显示模块引脚 GND 连接到 Arduino 引脚 GND 将LCD 显示引脚 SCL 连接到 Arduino 引脚 SCL ...
// enter the I2C address and the dimensions of your LCD here LiquidCrystal_I2C lcd(0x3F, 16, 2); 完成后,继续尝试草图。 #include <LiquidCrystal_I2C.h> LiquidCrystal_I2C lcd(0x3F,16,2); // set the LCD address to 0x3F for a 16 chars and 2 line display void setup() { ...
<LiquidCrystal_I2C.h>LiquidCrystal_I2C lcd(0x27, 16, 2); // set the LCD address to 0x27 for a 16 chars and 2 line display// 创建液晶屏对象// 参数1 液晶屏地址// 参数2和参数3 2行16列voidsetup(){ lcd.init(); // lcd初始化 lcd.backlight(); // 开启lcd背光灯 lcd.print("...
arduinoIDE里面有专门为lcd1602编写的库,打开项目->加载库->搜索LiquidCrystal_I2C 3.查找串口地址 首先需要知道LCD的串口地址,之后会用到 复制下面的代码,打开串口监视器,即可知道地址 #include <Wire.h> voidsetup() { Wire.begin(); Serial.begin(9600); ...
lcd.setBacklight(LOW);//Backlight offdelay(1000); lcd.setBacklight(HIGH);//Backlight on} 供电和耗电测试 硬件是Arduino NANO + 扩展板 + PCF8574T + 1602LCD, 使用输入电压12V. 扩展板本身不带IC, 只有一个电源LED, 功耗可以忽略. 在使用自带的LiquidCrystal_I2C库跑上面的测试代码时, 测得的功耗仅...
具体看模块手册 LiquidCrystal_I2C lcd(0x3F,16,2); void setup() { lcd.init(); // 初始化LCD lcd.backlight(); //设置LCD背景等亮 } void loop() { lcd.setCursor(0,0); //设置显示指针 lcd.print("LCD1602 iic Test"); //输出字符到LCD1602上 lcd.setCursor(0,1); lcd.print(" by L.L....
在控制一台I2C设备之前,我们首先必须找出其十六进制地址。 因此,我们的第一个示例是I2C HEX地址扫描器。 找到I2C LCD显示器的十六进制地址后,我们将相应地控制该显示器,以通过I2C从Arduino或NodeMCU向LCD显示器发送消息。 下图显示了I2C LCD显示屏分别与Arduino Uno和NodeMCU之间的硬件连接。
char array2[]="hello, world! "; //the string to print on the LCD int tim = 500; //the value of delay time // initialize the library with the numbers of the interface pins LiquidCrystal_I2C lcd(0x27,16,2); // set the LCD address to 0x27 0x3F for a 16 chars and 2 line dis...