constintSENSOR_PIN = 6;// Arduino 引脚连接到 18B20 传感器的 DQ 引脚 OneWire oneWire(SENSOR_PIN);// 设置一个 oneWire 实例 DallasTemperature sensors(&oneWire);// 将 oneWire 传递给 DallasTemperature 库 LiquidCrystal_I2C lcd(0x2
// 同一总线上可以有多个 DS18B20。 // 0指的是线上的第一个IC Serial.print(sensors.getTempCByIndex(0)); delay(500);// 延时500毫秒 } 实验串口返回情况(手摸传感器升温3度) Arduino实验场景图 程序二:串口显示温度 实验开源仿真编程(Linkboy V4.63) 实验串口返回情况 Arduino实验场景图 程序三:带工作指...
一、硬件准备Arduino ESP8266/ESP32开发板多路DS18B20温度传感器杜邦线若干面包板电源适配器二、硬件连接将...
The DS18B20 digital temperature sensor provides 9-bit to 12-bit celsius temperature measurements and has an alarm function with nonvolatile user-programmable upper and lower trigger points. The DS18B20 communicates over a 1-wire bus that by definition requires only one data line(and...
DS18B20传感器连接图 Arduino 实例代码 #include <DallasTemperature.h> DallasTemperature tempSensor; void setup(void) { Serial.begin(9600); tempSensor.begin(3); // Connect DS18B20 to Digital Pin 3 } void loop(void) { // Check if the sensor is working correctly ...
1.接线图 2.具体连线图 3.源代码如下 #include <LiquidCrystal.h>#include <OneWire.h>#include <DallasTemperature.h> #define TempSensor A0 OneWire oneWire(TempSensor);DallasTemperature sensors(&oneWire); // initialize the library with the numbers of the interface pinsLiquidCrystal lcd(12, 11, 5...
现在,使用一个简单的for(int i = 0; i < deviceCount; i++)循环,我们可以遍历传感器阵列,并i通过简单地调用以下命令读取DS18B20的温度:getTempCByIndex(i) 方法2:通过地址读取DS18B20 我们知道,每个DS18B20都分配有一个唯一的64位地址,以使它们彼此区分。在这种方法中,我们将找到该地址来相应地标记每个传感器。
DS18B20 Temperature Sensor module $1.89 4.7K resistor 400X 0.25w 1/4w Metal Film Resistor Pack Kit 1% 20 Value Each 20 Pcs 10 ~ 1M ohm $1.88 $5.50 See buying guide at the end of tutorial. EasyIoT server configuration In EasyIoT server add new node in Virtual driver. Node type is Te...
Serial.print(sensors.getTempCByIndex(0)); //获取0号传感器温度数据并发送 Serial.println("℃"); delay(1000); //一秒刷新一次 } 3.3.2 多路温度测量 (1)硬件连接 将两个DS18B20温度传感器的VCC和GND分别连接至Arduino Uno控制器的 5V和GND,以给两个DS18B20提供电源,两个DS18B20的DQ引脚接至ArduinoUno控制...
序列号。打印(tempF); 序列号。打印(“ \ xC2 \ xB0”);//显示度数符号 序列号。println(“ F”); 由于12位模式下的温度转换最多需要750 ms,因此我在每次测量之间增加了1秒的延迟。 在Arduino上使用多个DS18B20传感器 正如我在简介中提到的那样,您可以仅使用Arduino的一个引脚就可以从多个DS18B20传感器读取温...