如果输入“0”并发送,则可以查看当前继电器状态(为“ON”或“OFF”)。 如果您输入“1”,您将切换到继电器1,如果它是“OFF”为“ON”,如果是“ON”则为“OFF”。发送“2”则会对继电器2进行相同的操作。对于这两个继电器,状态保存在布尔型变量(“relay1State”和“relay2State”)中,并且对于每个继电器,LED会...
mySwitch.switchOn("11111","00010"); delay(1000); mySwitch.switchOff("11111","00010"); delay(1000); *//* Same switch as above, but using decimal code */mySwitch.send(5393,24);//5393表示发送的信号代码,24表示数据长度。 delay(1000);//暂停1000毫秒后再执行下一行代码。 mySwitch.send(53...
这是一个基于上述电路的非常基本的Arduino草图,当您将磁铁靠近开关时,它将点亮内置LED(连接到引脚13),当您将其移开时熄灭。 登录后复制constintREED_PIN =2;// Pin connected to reed switchconstintLED_PIN =13;// LED pinvoidsetup(){ Serial.begin(9600); pinMode(REED_PIN, INPUT_PULLUP);// Enable...
烧录代码 代码编译完没问题后,点击图中所选按钮将其上传至 Arduino UNO 板上。 手机设置 手机搜索蓝牙,输入密码并连接。 之后选择Switch mode。 对按键进行设置。 点击APP 上的开关,就能够实现控制 LED 了。 实际结果 LED 打开: LED 关闭: 心得总结 昨天晚上鼓捣了很久,都没有出现正确的结果,后来才发现,控制 ...
}// the loop function runs over and over again forevervoidloop(){digitalWrite(LED_BUILTIN, HIGH);// turn the LED on (HIGH is the voltage level)delay(1000);// wait for a seconddigitalWrite(LED_BUILTIN, LOW);// turn the LED off by making the voltage LOWdelay(1000);// wait for a...
();switch(type){case0:Serial.println("Unknown Controller type found ");break;case1:Serial.println("DualShock Controller found ");break;case2:Serial.println("GuitarHero Controller found ");break;case3:Serial.println("Wireless Sony DualShock Controller found ");break;}pinMode(input1,OUTPUT);pin...
当按钮1按下时,亮度增加,当按钮2按下时亮度减小。这个动作可以试试if...else if函数(实际想想,switch case、while 这几个函数都不适用这里。) 上面if语句里0<brightness<255,这个判定条件还是很必要的,不然你一直按按钮1,brightness数值就会不断增大,如果没有串口通讯的话,实际操作时你是不知道增大了多少的,当...
Serial.println("on"); // 向串口调试终端打印字符串 // “number of button pushes: ”,此处没有换行。 Serial.print("number of button pushes: "); // 接着上一行尾部,打印记录按键次数变量的数值。 Serial.println(buttonPushCounter); } else { // 向串口调试终端打印字符串“off”, // 表示当前按...
CPU frequency switch is compile-time only (#6833) Device tests device tests: some of them can be run on host (#6912) Add test for FS::open("w+") (#7241) Boot eboot: fix linking and padding (#7047) Allow GZIP compressed flash updates (#6820) Building on host host build: ...
* Momentary switch attached from pin 2 to ground * Built-in LED on pin 13 Unlike pinMode(INPUT), there is no pull-down resistor necessary. An internal 20K-ohm resistor is pulled to 5V. This configuration causes the input to read HIGH when the switch is open, and LOW when it is close...