#define SPI_CLOCK_DIV ((int) 21) //输出模式 布尔值 RDATA_MODE = true; //true - RDATA;false - RDATAC 布尔CAPTURE_DATA_MODE = false;// true -读取 ADC;false -读取环路 中的寄存器#define pinport PIOB #define pinmask (1<<25)// Arduino 引脚2是端口 B 引脚25 (请参阅...
printf("read %d byte data end, spi frequency: %ld, time: %f sn", test_size, SPI_FREQUENCY, (lTime / 1000000.0)); if(buf) { free(buf); } 速度测试结果如下: 我这里只测试了GD25Q64,没有测试W25Q128,读写速度应该是差不多的。 SPI 40MHz读写1MB数据测试: SPI 20MHz读写1MB数据测试: ...
Arduino库教程-SPI-Barometric Pressure SensorUsing SPI to read a Barometric Pressure Sensor(用SPI来读取气压传感器) 这个例子展示了如何使用SPI(串行外设接口)通讯库从SCP1000气压传感器读取数据。更多关于SPI的信息,请点击这里。 硬件要求 Arduino or Genuino board SCP1000 气压传感器分接板(Breakout Board) 连接...
88. data = spi_transfer(0xFF); //get data byte89. digitalWrite(SLAVESELECT,HIGH); //release chip, signal end transfer90. return data;91. }92.93. void loop()94. {95. eeprom_output_data = read_eeprom(address);96. Serial.print(eeprom_output_data,DEC);...
Arduino shiftIn is a purely software implementation of a serial input interface; The equivalent hardware interface is SPI (Although shiftIn() represents half of that interface i.e. the data input part).Many chips use a serial interface to reduce the number of physical pins, so instead of usi...
#include <SPI.h>//bps 57600/*连线,板子就剩一个管脚rq没连接Arduino RC522 (工作电压3.3V)D5 <---> RST (这个脚不接貌似也可以)D10 <---> SDA (在RC522中即为CS)D11 <---> MOSID12 <---> MISOD13 <---> SCK地和3.3均需连接~~~down close com5run open com5*/#define uchar unsig...
This is very fast (as fast as possible // without compression or data loss), and easy to parse, but impossible to read // for a human. //#define OUTPUT_BINARY_ACCELGYRO #define LED_PIN 2 bool blinkState = false; void setup() { // join I2C bus (I2Cdev library doesn't do this...
今天我们将学习另一种串行通信协议:I2C(Inter Integrated Circuits)。I2C与SPI相比,I2C只有两根线,SPI使用四根线,I2C可以有多个主从,而SPI只能有一个主和多个从。因此,在一个项目中有多个微控制器需要成为主控,然后使用 I2C。I2C通信一般用于与陀螺仪、加速度计、气压传感器、LED显示屏等进行通信。
软件模拟SPI通信 实验:使用 74HC595 串口通信简介 arduino支持的串行通信有UART,I2C和SPI三种通信协议方式 根据串行数据的传输方向,我们可以将通信分为单工,半双工,双工 单工 是指数据传输仅能沿一个方向,不能实现反向传输 半双工 是指数据传输可以沿两个方向,但不能同时进行传输 ...
打开ArduinoIDE,选择 文件--示例--U8g2--full_buffer--HelloWorld 修改程序中的一段 U8G2_SH1106_128X64_NONAME_F_4W_SW_SPI u8g2(U8G2_R0, /* clock=*/ 15, /* data=*/ 16, /* cs=*/ 10, /* dc=*/ 4, /* reset=*/ 6); 3、接线图 4、显示效果...