下面定义在我们的SPI通讯中要用到的pins引脚,DATAOUT, DATAIN, SPICLOCK和SLAVESELECT。然后定义EEPROM的控制指令(opcodes): 接下来分配程序会用到的全局变量。我们将用char buffer[128]来保存要传输到EEPROM的数据: 首先我们初始化我们的串口连接,设置我们的input和output模式并设置SLAVESELECT线为高时开始。这个设置...
语法:SPI.pins(sck, miso, mosi, ss) 参数: sck,时钟引脚,固定为6; miso,主设备输入,从设备输出引脚,固定为7; mosi,主设备输出,从设备输入,固定为8; ...
通过SPI,ESP32可以与其他同样使用SPI连接的传感器相互传输数据。 SPI的传输采用同步的时间线,也称为共享时钟信号,这有助于确保传输的数据准确一致。 SPI主要应用于需要短距离、高速串行通信的场景,例如需要快速同步数据的显示屏、SD卡读取器、加速度传感器等。 可以将SPI想象成一种精密的对话方式,其中主设备(ESP32)和...
;// OPTION 2 lets you interface the display using ANY TWO or THREE PINS,// tradeoff being that performance is not as fast as hardware SPI above.//#define TFT_MOSI 11 // Data out//#define TFT_SCLK 13 // Clock out// For ST7735-based displays, we will use this call//Adafruit_ST77...
// OPTION 1 (recommended) is to use the HARDWARE SPI pins, which are unique // to each board and not reassignable. For Arduino Uno: MOSI = pin 11 and // SCLK = pin 13. This is the fastest mode of operation and is required if ...
The AD5206 has 6 potentiometer channels. Each channel's pins are labeled A - connect this to voltage W - this is the pot's wiper, which changes when you set it B - connect this to ground. The AD5206 is SPI-compatible,and to command it, you send two bytes, ...
(recommended) is to use the HARDWARE SPI pins, which are unique// to each board and not reassignable. For Arduino Uno: MOSI = pin 11 and// SCLK = pin 13. This is the fastest mode of operation and is required if// using the breakout board's microSD card.// For 1.44" and 1.8"...
下面定义在我们的 SPI 通讯中要用到的 pins 引脚,DATAOUT, DATAIN, SPICLOCK 和 SLAVESELECT。然后定义 EEPROM 的控制指令(opcodes):接下来分配程序会用到的全局变量。我们将用 char buffer[128]来保存要传输到 EEPROM 的数据: 首先我们初始化我们的串口连接,设置我们的 input 和 output 模式并设置 SLAVESELECT...
Arduino Due 是一块基于 Atmel SAM3X8E CPU的微控制器板.它是第一块基于 32位ARM核心的arduino. 它有54个数字IO口 (其中12个可用于PWM输出),12个模拟输入口,4路UART硬件串口, 84 MHz的时钟频率, 一个USB OTG接口, 两路DAC(模数转换),两路TWI,一个电源插座,一个SPI接口,一个JTAG接口,一个复位按键和一...
将指定的引脚配置成输出或输入。详情请见digitalpins。 语法: pin Mode(pin, mode) 参数: pin:要设置模式的引脚 mode:INPUT或OUTPUT 返回 无 例子: led Pin=13//LED连接到数字脚13 voidsetup() { pin Mode(led Pin, OUTPUT) ;//设置数字脚为输出 } voidloop() { digital Write(ledPin, HIGH) ;//点...