int analogPin = 3;//使用analog in 引脚3 作为电压标记 int val = 0; // 读取到的电压值 void setup() { Serial.begin(9600); //串口传输波特率 1s传输的字节 } void loop() { val = analogRead(analogPin); // 读取输入的电压值 Serial.println(val);
int ledPin = 9; // LED connected to digital pin 9 int analogPin = 3; // potentiometer connected to analog pin 3 int val = 0; // variable to store the read value void setup() { pinMode(ledPin, OUTPUT); // sets the pin as output } void loop() { val = analogRead(analogPin)...
格瑞图:Arduino-0017-内置示例-模拟输入串口输出 AnalogInOutSerial 格瑞图:Arduino-0018-内置示例-模拟输入 AnalogInput 1、示例代码及解析 (1)代码 /*Mega analogWrite() testThis sketch fades LEDs up and down one at a time on digital pins 2 through 13.This sketch was written for the Arduino Mega, ...
int analogPin = 5;int val = 0;void setup(){Serial.begin(9600);}void loop(){val = analogRead(analogPin);Serial.println(val);}这里还是要实现Matlab的即时读取和画图。Matlab代码如下:s = serial('COM3'); %定义串口对象set(s,'BaudRate',9600); %设置波特率sfopen(s); %打开串口对象sinterval...
Pin numbers: Matrix: * Digital pins 2 through 13, * analog pins 2 through 5 used as digital 16 through 19 Potentiometers: * center pins are attached to analog pins 0 and 1, respectively * side pins attached to +5V and ground, respectively. ...
Analog 3 #define LCD_CD A2 // Command/Data goes to Analog 2 #define LCD_WR A1 // LCD Write goes to Analog 1 #define LCD_RD A0 // LCD Read goes to Analog 0 #define LCD_RESET A4 // Can alternately just connect to Arduino's reset pin #include <Adafruit_GFX.h> // Hardware-...
#define ANALOG_PIN A0 #define OLED_RESET -1 // 重置引脚 #(如果共享 Arduino 重置引脚,则为 -1) Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, OLED_RESET); doublevImag[SAMPLES]; doublevReal[SAMPLES]; unsignedlongsampling_period_us; ...
analogWrite(thisPin, brightness); delay(2); } // pause between LEDs: delay(100); } } [Get Code] 更多 for() analogWrite() delay() AnalogInOutSerial - 读取一个模拟输入引脚,按比例划分读数,然后用这个数据来熄灭或者点亮一个LED灯 AnalogInput - 用电位计来控制LED灯闪烁 ...
make sure the pin is in output mode// for consistenty with Wiring, which doesn't require a pinMode// call for the analog output pins.pinMode(pin,OUTPUT);if(val==0){digitalWrite(pin,LOW);}elseif(val==255){digitalWrite(pin,HIGH);}else{switch(digitalPinToTimer(pin)){// XXX fix neede...
analogWrite(thisPin, brightness); delay(2); } // pause between LEDs: delay(100); } } [Get Code] 更多 for() analogWrite() delay() AnalogInOutSerial - 读取一个模拟输入引脚,按比例划分读数,然后用这个数据来熄灭或者点亮一个LED灯 AnalogInput - 用电位计来控制LED灯闪烁 ...