Serial.begin(baudrate):该函数初始化串口通信,并设置波特率。 Serial.print(value):该函数将指定值打印到串口。 Serial.println(value):该函数将指定值打印到串口,并在末尾添加一个换行符。 例如,以下代码将初始化串口通信并设置波特率为9600,在循环中读取来自计算机的数据并打印它们: ``` void setup() { Serial...
Using Programmer : urclock Overriding Baud Rate : 115200 AVR Part : ATmega328 Chip Erase delay : 9000 us PAGEL : PD7 BS2 : PC2 RESET disposition : possible i/o RETRY pulse : SCK Serial program mode : yes Parallel program mode : yes Timeout : 200 StabDelay : 100 CmdexeDelay : 25 Sy...
voidsetup(){// Set MIDI baud rate:Serial.begin(31250);}voidloop(){// play notes from F#-0 (0x1E) to F#-5 (0x5A):for(intnote=0x1E;note<0x5A;note++){//Note on channel 1 (0x90), some note value (note), middle velocity (0x45):noteOn(0x90,note,0x45);delay(100);//Note...
display.begin(SSD1306_SWITCHCAPVCC, 0x3C); //initialize OLED with I2C address 0×3C //Serial.begin(115200); //Initialize baud rate particleSensor.begin(Wire, I2C_SPEED_FAST); //Use default I2C port, 400kHz speed particleSensor.setup(); //Configure sensor with default settings particleSensor...
import serial ser = serial.Serial() ser.baudrate = 9600 # 设置波特率 ser.port = 'COM6' # 端口是COM3 print(ser) ser.open() # 打开串口 print(ser.is_open) # 检验串口是否打开 # board = Arduino('COM3') """ def duoji (): ...
Serial.begin(BAUD_RATE); Wire.begin(); delay(1000); // 给OpenMV一个启动的时间 } void loop() { int32_t temp = 0; char buff[CHAR_BUF] = {0}; Wire.requestFrom(0x12, 2); if (Wire.available() == 2) { // got length?
Serial.begin(baudrate); // connect to the serial port Serial.setTimeout(20); Serial.println("Starting Cam-servo Face tracker"); pinMode(servopinx, OUTPUT); // declare the LED's pin as output servox.attach(servopinx); // center servos ...
MultiSerialMega - 使能Arduino Mega上2个串口。 PhysicalPixel - 通过从Processing或者Max/MSP发送数据到Arduino上,使LED开关。 ReadASCIIString - 分析整数里一个用逗号分隔的字符串,来使一个LED灯褪色。 SerialCallResponse - 通过一个呼-应的方法(握手)来发送多个变数 SerialCallResponseASCII - 通过一个呼-应的...
your setup code here, to run once:Serial.begin(9600);HekrInit(SendChar);HekrModuleControl(HekrConfig);}void loop() {GetData();DataHandle();}void SendChar(unsigned char ch){Serial.write(ch);delay(2);}void GetData(void){u8 i = 0;while(Serial.available()){ RecvBuffer[i++] = Serial...
Digital Read Serial:读取开关量,将状态发布到Arduino串行监视器。...Multi Serial Mega:使用Arduino Mega上提供的两个串行端口。...Virtual Color Mixer:将多个变量从Arduino发送到您的计算机,并在Processing或Max / MSP中读取它们。...Keyboard Reprogram:在Arduino IDE中打开一个新窗口,并使用简单的闪烁程序重新...