// read the input on analog pin 0: int sensorValue = analogRead(A0); // Convert the analog reading (which goes from 0 - 1023) to a voltage (0 - 5V): float voltage = sensorValue * (5.0 / 1023.0); // print out the value you read: Serial.println(voltage); } 代码功能 读取电位...
2、读取模拟电压 - Read Analog Voltage Reads an analog input and prints the voltage to the Serial Monitor. 读取模拟输入并打印电压值到串口监视器。 This example shows you how to read an analog input on analog pin 0, convert the values from analogRead() into voltage, and print it out to the...
void loop() { // read the input on analog pin 0: int sensorValue =analogRead(A0); // Convert the analog reading (which goes from 0 - 1023) to a voltage (0 - 5V): float voltage = sensorValue * (5.0 / 1023.0); // print out the value you read: Serial.println(voltage); } 火...
Serial.println(voltage) 现在,当你打开你在Arduino IDE软件上的串口监视器(可以通过键盘快捷键Ctrl+Shift+M打开),你应该看到一个范围从0.0-5.0的稳定的数据流。随着你转动那个旋钮,这个输入到A0引脚的电压值会随之变化。 /* ReadAnalogVoltage Reads an analog input on pin 0, converts it to voltage, and pr...
/*ReadAnalogVoltage 读取模拟电压 Reads an analog input on pin 0, converts it to voltage, and prints the result to the serial monitor. OPEN THE SERIAL MONITOR TO VIEW THE OUTPUT >> Attach the center pin of a potentiometer to pin A0, and the outside pins to +5V and ground. ...
Serial.println(voltage) 现在,当你打开你在Arduino IDE软件上的串口监视器(可以通过键盘快捷键Ctrl+Shift+M打开),你应该看到一个范围从0.0-5.0的稳定的数据流。随着你转动那个旋钮,这个输入到A0引脚的电压值会随之变化。 /* ReadAnalogVoltage Reads an analog input on pin 0, converts it to voltage, and pr...
格瑞图:Arduino-0007-内置示例-读取模拟电压 Read Analog Voltage 格瑞图:Arduino-0008-内置示例-非延迟闪烁 Blink Without Delay 格瑞图:Arduino-0009-内置示例-按钮 Button 格瑞图:Arduino-0010-内置示例-去抖 Debounce 格瑞图:Arduino-0011-内置示例-数字输入上拉 DigitalInputPullup ...
In Arduino, analog input usually refers to the voltage value from the sensor, buttons, or other analog device through the analog pins of Arduino. There are multiple simulation pins on the Arduino board (usually marked as A0-A5), which can be used to read analog signals.以下是一个简单的...
BareMinimum - 需要开始一个新的程序的最简框架 Blink - 使LED灯开和关 DigitalReadSerial - 读取一个开关,打印其状态到Arduino串口监视器 Fade - 示范怎么用模拟输出来使LED灯的亮度变淡 ReadAnalogVoltage - 读取一个模拟输入,并打印电压值到串口监视器...
Create an Arduino object and read voltage from analog input pin. Get a = arduino; readVoltage(a,'A4') ans = 1.0606 Specify Number of Samples and Sample Rate Since R2025a This example uses: MATLAB Support Package for Arduino Hardware Copy Code Copy Command Create an arduino object and re...