Using SPI to read a Barometric Pressure Sensor(用SPI来读取气压传感器) 这个例子展示了如何使用SPI(串行外设接口)通讯库从SCP1000气压传感器读取数据。更多关于SPI的信息,请点击这里。 硬件要求 Arduino or Genuino board SCP1000 气压传感器分接板(Breakout Board) 连接线 电路 图由Fritzing 软件绘制 原理图 SCP...
STS35 temperature sensor and Arduino example In this article we look at a temperature and pressure sensor, the STS35 temperature sensor from Sensirion, and connect it to an Arduino R4, you can use an older Arduino Uno. It will work just fine. Sensor Information The STS3x-DIS … Read more...
STS35 temperature sensor and Arduino example In this article we look at a temperature and pressure sensor, the STS35 temperature sensor from Sensirion, and connect it to an Arduino R4, you can use an older Arduino Uno. It will work just fine. Sensor Information The STS3x-DIS … ...
Bosch BMP180 pressure sensor library for the Arduino microcontroller Mike Grusin, SparkFun Electronics Uses floating-point equations from the Weather Station Data Logger project http://wmrx00.sourceforge.net/ http://wmrx00.sourceforge.net/Arduino/BMP085-Calcs.pdf Forked from BMP085 library by M...
转到文件>示例>SparkfunBMP180 > SFE_BMP180_example。这个例子对传感器如何读取压力、温度和计算高度进行了很好的评论和解释。/* SFE_BMP180库示例草图 与大多数压力传感器一样,BMP180测量绝对压力。 这是设备所感知到的实际环境压力,会随着海拔和天气的变化而变化。 在进行压力读数之前,必须进行温度读数。 这是...
更多关于传感器怎样工作,参考the Barometric Pressure Sensor example。 硬件要求 Arduino 或者 Genuino 开发板 SCP1000 压力传感突破板 Arduino Ethernet Shield 电路 气压传感器连接到你的Arduino或genuino /以太网sheild组合板的引脚6,7和11 - 13,并通过设备的3.3V输出提供电源。连接传感器的DRDY引脚(数据准备就绪)...
Arduino FSR 0.5 压力感应电阻传感器用户手册说明书 User Manual ARDUINO SENSOR FORCE RESISTOR 0.5 Overview:FSRs are sensors that allow you to detect physical pressure, squeezing and weight. They are simple to use and low cost. This is a photo of an FSR, specifically the Interlink 402 model. ...
Software Serial Example Two Port Receive SPI(串行外设接口) Barometric Pressure Sensor Digital Pot Control Stepper(步进机) Motor Knob Stepper One Revolution Stepper One Step At A Time Stepper Speed Control 有线(Wire) Digital Potentiometer Master Reader/Slave Writer ...
The code below is a nice example of how to do this. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 #include "Wire.h" // imports the wire library for talking over I2C #include "Adafruit_BMP085.h" // import the Pressure Sensor Library ...
fix(zigbee): Fixed Guru Meditation crash with Zigbee Analog example by @oli-the-kitty in #11064 fix(zigbee): Use correct attributeID in setAnalogInputReporting by @P-R-O-C-H-Y in #11065 feat(Zigbee): Adding Zigbee Wind speed sensor endpoint by @lboue in #10455 feat(zigbee): Save ne...