#define SCREEN_HEIGHT 64 // OLED display height, in pixels // Declaration for an SSD1306 display connected to I2C (SDA, SCL pins) #define OLED_RESET 4 // Reset pin # (or -1 if sharing Arduino reset pin) Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, OLED_RESET);...
之前我发了一个显示器流光溢彩的视频,颜色效果还是很不错的。本文就给大家说说制作方法,过程非常简单,相信每个人都可以轻松搞定。显示器流光溢彩1、准备材料需要用到的材料如下:ws2812b灯带(带背胶);arduino (nano、uno都ok);usb线;导线(杜邦线);AmbiBox软件;arduino软件;2、贴灯带和接线将灯带贴到显示器背面,具...
delay(500); display.display();//把缓存的都显示} 由于nano板内存太小,名字和单位都不能放,只是显示了数据 __EOF__
2. Products in the original Nano V3.0 motherboard upgraded to with 0.91-inch OLED display, resolution 128 * 32, more convenient and clearer to use3. Main control chip: ATmega328P, serial chip: CH340C4. Diversified product interface options, three optional: MINI USB interface, Micro USB ...
Arduino:1.8.7 (Windows 10), 开发板:"Arduino Nano, ATmega328P (Old Bootloader)"ssd1306_128x64_i2c:34:46: error: variable 'logo16_glcd_bmp' must be const in order to be put into read-only section by means of '__attribute__((progmem))'exit...
(如果共享 Arduino 重置引脚,则为 -1) Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, OLED_RESET); double vImag[SAMPLES]; double vReal[SAMPLES]; unsigned long sampling_period_us; arduinoFFT fft = arduinoFFT(vReal, vImag, SAMPLES, SAMPLING_FREQ); //调整参考以去除背景噪声 ...
代码运行次数:0 运行 AI代码解释 voidsetup(){// initialize serial communication at 9600 bits per second:Serial.begin(9600);}// the loop routine runs over and over again forever:voidloop(){// read the input on analog pin 0:int sensorValue=analogRead(A0);// print out the value you read:...
updated GxEPD2_display_selection_new_style.h: added Arduino Nano Every, Arduino Nano ESP32, Arduino Nano IoT.Version 1.5.9added Power Save command (PWS) to GDEY075T7 init (issue with dithered bitmaps) added support for GDEY0579T93 5.79" b/w 792x272, SSD1683 added support for GDEY0579...
现在,用导线连接操纵杆电位器到GND,5V和信号。然后将操纵杆和滑动开关螺丝固定在控制器中间。在顶部添加触发开关和电位器。最后,将Arduino NANO开发板粘在一个角落上。 好的,现在,非常重要的一步你要把小的buck转换器设置为3.3V,然后把电位计粘在一起。然后将其连接到NRF24模块。最后,将所有的电线连接到Arduino...
display.begin(SSD1306_SWITCHCAPVCC, 0x3C); display.setTextColor(WHITE);//开像素点发光 display.clearDisplay();//清屏 display.setTextSize(2);//设置字体大小 display.setCursor(0, 0);//设置显示位置 display.println("-TonyCode-");//输出字符 ...