硬声是电子发烧友旗下广受电子工程师喜爱的短视频平台,推荐Arduino Nano驱动I2C接口0.96寸OLED显示屏模块视频给您,在硬声你可以学习知识技能、随时展示自己的作品和产品、分享自己的经验或方案、与同行畅快交流,无论你是学生、工程师、原厂、方案商、代理商、终端商...上
带I2C的Arduino 26x2 LED显示屏 带有idiotware shield的I2C OLED显示器中的动画 使用OLED显示器的低频示波器 2次下载 基于Arduino和OLED的元胞自动机 0次下载 由Arduino Nano供电的微型细胞自动机 0次下载 带I2C显示屏的Arduino遥控车 带LCD I2C 16x2显示屏的Arduino DTH22湿度温度 I2C OLED显示屏的51...
由于OLED显示器采用I2C通信协议,因此布线非常简单。您只需要连接到Arduino Uno I2C引脚,如下表所示。 Pin 连接到Arduino Uno Vin 5V GND GND SCL A5 SDA A4 如果您使用的是其他Arduino板,请确保检查正确的I2C引脚: Nano:SDA(A4);SCL (A5); MEGA:SDA(20);SCL (21); Leonardo:SDA(20);SCL (21); 库 ...
The display is connected by utilizing the i2c pins on your arduino. Which pins to use for this differs on some arduino models, but on the UNO and NANO you use pin A4 (SDA) and A5 (SCL). If you’re using another arduino, google the pinout and look for SDA and SCL pins. (For ex...
1、首先我们需要修改树莓派的配置文件使能I2C,通过nano编辑器修改raspi-blacklist.conf 文件内容pi@raspberrypi ~ $ sudo nano /etc/modprobe.d/raspi-blacklist.conf# blacklist spi and i2c by default (many users don't need them)blacklist spi-bcm2708blacklist i2c-bcm27082、打开/etc/modules ,在...
0.91寸OLED模块引脚说明 GND 地线 VCC 电源 (因为模块内部自带稳压,所以3.3~5V供电都是ok的) SDA I2C 数据线(接A4) SCL I2C 时钟线(接A5) (可以看到模块后面有一个U2芯片,就是用来稳压的) 项目之九:综合测试,中文显示 Arduino实验开源代码 /*
display.setTextColor(WHITE);//开像素点发光 display.clearDisplay();//清屏 display.setTextSize(2); //设置字体大小 display.setCursor(0, 0);//设置显示位置 display.println("-TonyCode-");//输出字符 display.drawBitmap(32, 16, str1, 16, 16, 1); //画出字符对应点阵数据 ...
运行SSD1306 Example 例子- 输出直线和文字以及文字滚动, 例子中能明显看出文字滚动时参数的含义 #include <SPI.h>#include<Wire.h>#include<Adafruit_GFX.h>#include<Adafruit_SSD1306.h>#defineOLED_RESET 4Adafruit_SSD1306 display(OLED_RESET);#if(SSD1306_LCDHEIGHT != 64)#error("Height incorrect, plea...
https://e2e.ti.com/support/sensors-group/sensors/f/sensors-forum/624549/ldc1614evm-ldc-1614-i2c-connection-with-arduino-nano 器件型号:LDC1614EVM 尊敬的会员: 将LDC 1614与 Arduino Nano (5V 设备)连接时遇到一些问题。 与 Arduino 建立连接。 我执行了以下操作: ...
运行SSD1306 Example 例子- 输出直线和文字以及文字滚动, 例子中能明显看出文字滚动时参数的含义 #include <SPI.h>#include<Wire.h>#include<Adafruit_GFX.h>#include<Adafruit_SSD1306.h>#defineOLED_RESET 4Adafruit_SSD1306 display(OLED_RESET);#if(SSD1306_LCDHEIGHT != 64)#error("Height incorrect, plea...