带按钮的 Arduino Nano 接线 注意:按钮引脚可以连接到 Arduino Nano D4 或任何其他数字输入引脚。 按钮的 Arduino 代码 我们定义了一个结构体(称为button )来表示按钮的状态。串行监视器将实时输出该状态。 #define BUTTON_PIN 4 struct button { byte pressed = 0; }; button
// 激光引脚 const int Laser_Pin=5; int buttonState = 0; // 触摸传感器引脚 const int buttonPin = 2; / // Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, -1); Adafruit_MLX90614 mlx = Adafruit_MLX90614(); # oled12864,gy906都使用i2c通信 # A4 SDA A5 SCL void setup()...
2.AnalogRead() 模拟IO口读函数,Arduino中ADC单元是10位分辨率 analogRead(pin) pin:不同的核心电路板不同的模拟输入口数量,一般是0-5,如Arduino Uno; 0-7 Arduino Mini and Arduino Nano;0-15 Arduino Mega2560 3.AnalogWrite() 数字IO口PWM输出函数 analogWrite(pin,Value) pin:3,5,6,9,10 ;在Arduino M...
(RS、EN、D4、D5、D6、D7); 按钮UP_Button ( 16 , 25 , false , true ) ; 按钮Down_Button ( 15 , 25 , false , true ) ; 无效 设置() { pinMode(PWM_Pin,输出); pinMode(扬声器,输出); 模拟写入(PWM_Pin,PWM_Value); UP_Button.begin(); Down_Button.begin(); lcd.setCursor( 0 ...
红外接收二极管的VCC引脚连接到Arduino NANO的VCC引脚,OUT引脚连接到Arduino的D2引脚。 3.1.2 红外发射与接收代码 #include <IRremote.h> //红外 接收 int RECV_PIN = 2; IRrecv irrecv(RECV_PIN); decode_results results; //红外 发射 IRsend irsend; void setup(void) { //红外 初始化 Serial.begin(...
Rather then requiring a physical press of the reset button before an upload, the Arduino Nano is designed in a way that allows it to be reset by software running on a connected computer. One of the hardware flow control lines (DTR) of the FT232RL is connected to the reset line of the ...
(9600);pinMode(buttonPin,INPUT);//设置7号引脚为输入引脚pinMode(buttonPin,LOW);radio.begin();//启动nrf24模组radio.openWritingPipe(address);//设定通道地址radio.setPALevel(RF24_PA_MIN);//设定广播功率radio.stopListening();//停止监听,设定成发射模式}voidloop(){delay(2500);// boolean touch_...
本文利用PS2手柄和Arduino开发板制作了一个简易的遥控小车,利用蓝牙进行通信,可以实现前后左右的移动。(原理掌握之后可以自己拓展相关功能) 一、零件 1.Arduino UNO开发板: ArduinoUNO是ArduinoUSB接口系列的最新版本,作为Arduino平台的参考标准模板。UNO的处理器核心是ATmega328,同时具有14路数字输入/输出口(其中6路可作...
Before we begin I want to make sure we’re all using the same terms. There are two main categories of interrupts: Hardware and Software. A Hardware interrupt is triggered by something outside of the chip like a button while a Software interrupt is triggered from inside the chip like a ...
百度试题 结果1 题目Arduino UNO/Nano主控板,pinMode函数中,设置数字引脚为输入模式的参数有?( ) A. INPUT B. OUTPUT C. INPUT_PULLUP D. INPUT_PULLDOWN 相关知识点: 试题来源: 解析 AC 反馈 收藏