5个LED灯通过串联的220 ohm电阻连接到数字引脚pin 2,3,4,5,6。 为了使程序工作,你的开发板需要连接到电脑。在Arduino IDE上打开串口监视器,并且发送字符 a,b,c,d,e来点亮相应的LED灯,或者其他东西来关闭它们。 图为Fritzing软件绘制。 原理图 样例代码 /* Switch statement with serial input Demonstrates th...
带状态机的Arduino状态机 所以我想做一个状态机,从用户那里得到一个输入字母,然后用LED输出莫尔斯电码。我用了一个开关,但由于某种原因它不想工作。它只对字母a有效,当我再加一个字母时它就停止工作了。 我使用了3个功能(点,线和暂停),并结合他们的LED闪烁。我们学校不允许使用“delay()”,所以我做了一个计时...
FastLED.addLeds<NEOPIXEL,LED_PIN>(leds, NUM_LEDS); for (int i = 0; i < NUM_LEDS; i++) leds[i] = CRGB(0, 0, 255); FastLED.show(); delay(1000); //bootstrap average with some low values for (int i = 0; i < AVGLEN; i++) { insert(250, avgs, AVGLEN); } //Initial...
关键字break可用于退出switch语句,通常每条case语句都以break结尾。如果没有break语句,switch语句将会一直执行接下来的语句(一直向下)直到遇见一个break,或者直到switch语句结尾。 语法也是先switch然后跟括号()括号内写上变量值,后面跟大括号,大括号里写上case分支 例子 switch (var) { case 1://case 1后面是冒号 ...
#define LED LED_BUILTIN void setup(void) { Serial.begin(115200); Serial.println("Action of Arduino switch case replacing if else"); digitalWrite(LED, LOW); pinMode(LED,OUTPUT); } void loop(void) { int command = 0; if (Serial.available() ) { char ch = Serial.read(); switch(ch)...
将LED连接到Arduino的数字输出引脚可以打开和关闭LED。此外,我们还需要给LED连接一个电阻器,以防止过电流(关于更详细的LED使用方法,请参阅“Arduino基础:通过数字输出来控制LED照明”(https://techclass.rohm.com.cn/knowledge/tech-info/how-tos/arduino/the-basics-of-arduino-control-led-lighting-with-digital-ou...
另一个例子,使用 for循环使 LED产生渐亮渐灭的效果: voidloop() { intx=1; for(inti=0;i>-1;i=i+x) { analogWrite(PWMpin,i); if(i==255)x=-1; // 在峰值转变方向 delay(10); } } 2.4 switch case switch/ case语句 和if语句相同,switch…case通过程序员设定的在不同条件下执行的代码控制...
如电路图所示,一个按钮直接连接到Arduino的引脚A0(ENREGISTRATION),A1(DEL),A2(UP),A3(DOWN)相对于地面,黄色LED通过1k电阻连接到Arduino的数字引脚D7相对于接地。指纹模块的 Rx 和 Tx 直接连接到 Arduino 的串行引脚 D2 和 D3(软件串行)。5v电源用于为取自 Arduino 板的指纹模块供电。蜂鸣器也连接在引脚 A5...
/* Replace the line below with the display initialization function, you want to use */ ssd1306_128x32_i2c_init(); ssd1306_clearScreen(); /* Set font to use with console */ ssd1306_setFixedFont(ssd1306xled_font6x8); } void loop() { ...
{ /* Replace the line below with the display initialization function, you want to use */ ssd1306_128x32_i2c_init(); ssd1306_clearScreen(); /* Set font to use with console */ ssd1306_setFixedFont(ssd1306xled_font6x8); } void loop(){ static uint8_t i = 0; /* Here use any ...