IR(Infrared Remote)即红外遥控。每按下一个键,即产生具有不同编码的数字脉冲,这种代码指令信号通过调制激励红外光二级管产生具有脉冲串的红外波,通过空间的传送到受控机内的遥控接收器。在接收过程中,红外波信号通过光学滤波器和光电二极管转换为电信号,此信号经过放大、检波、整形、解调、送到解码与接口电路,从而完成...
/** IR REMOTE CONTROL + RGB* by Hanie Kiani* https://electropeak.com/learn/*/#include ...
本篇介绍红外遥控相关原理及应用,通过红外遥控器控制 Uno 板载 LED 灯。 红外遥控原理 红外遥控主要由红外发射和红外接收两部分组成。 红外发射和接收的信号其实都是一连串的二进制脉冲码,高低电平按照一定的时间规律变换来传递相应的信息。为了使其在无线传输过程中免受其他信号的干扰,通常都将信号调制在特定的载波频率...
int ir_code=0x00;//命令值 //定时器初始化函数 void timer1_init(void) { TCCR1A = 0X00; TCCR1B = 0X05;//给定时器时钟源 TCCR1C = 0X00; TCNT1 = 0X00; TIMSK1 = 0X00; //禁止定时器溢出中断 } //执行译码结果函数 void remote_deal(void) { switch(ir_code) { case 0xfe01://VOL...
In the below switch-case replace the numbers with the IR codes from your remote. Make sure you write the code that gets printed in your serial monitor from line 142. */ voidacceptInput(intcharacter) { Serial.println(character); switch(character) { ...
irrecv.enableIRIn();pinMode(ledPin,OUTPUT);//设置LED为输出状态}voidloop(){// put your main code here, to run repeatedly:if(IrReceiver.decode()){//判断是否接收到信号Serial.println(IrReceiver.decodedIRData.decodedRawData,HEX);if(IrReceiver.decodedIRData.decodedRawData ==0xFF00BF00){//如果...
蓝牙收到的信息将基于我们将在下一步中安装的Android应用程序上按下的按钮。收到信息后,我们只需要触发相应的IR代码,如下所示 if (BluetoothData == '2') { irsend.sendRaw(Temp23, sizeof(Temp23) / sizeof(Temp23[0]), khz); delay(2000);//Send signal to set Temperatue 23C ...
对于锁存开关,使用代码:Code_ArduinoUNO_EEPROM_WiFi_IR_Switch_4Relay.ino 为Arduino 物联网云配置 Alexa 应用程序 从Google Play 商店或 App Store下载并安装Amazon Alexa App 。 点击“更多”。 然后选择“技能和游戏”。 搜索Arduino 并点击“Arduino”。
AnalysIRRevision: 1.0This code is provided to overcome an issue with Arduino IR librariesIt allow...
当我试图上载或验证我的Arduino代码时,会弹出以下错误:如果你看不见,上面写着: [Starting] Verify sketch - ir_remote\ir_remote.ino [Arduino: This application was configured to use a bundled Java Runtime Environment but the runtime is[Error] Exit with code 浏览4提问于2020-06-30得票数 2 回答...