input_volt = temp / (r2/(r1+r2)); 在这里,我们在Arduino的LCD和串行监视器上显示了测量的电压值。因此,在代码中,Serial.println用于在串行监视器上打印值,lcd.print用于在16x2 LCD上打印值。 Serial.print("v= "); // prints the voltage value in the serial monitor Serial.println(input_volt); lc...
代码中指定的模拟输入值: 登录后复制Serial.print(" analog input ") ;// this gives name which is “analog input” to the printed analog valueSerial.print(m);// this simply prints the input analog value 代码中指定的所需交流电压: 登录后复制Serial.print(" ac voltage ") ;// this gives name...
INPUT 输入模式 OUTPUT 输出模式 INPUT_PULLUP 输入上拉模式 Blink程序中使用到的pinMode(LED_BUILTIN, OUTPUT): 即是把LED_BUILTIN(13号)引脚配置为输出模式 配置成输出模式后,还需要使用digitalWrite() 让其输出高电平或者是低电平。其调...
接收到红外信号后,使用 if-else 语句将红外信号编码与数字 0~9、符号 +、- 对应,并赋值到变量 Input。根据变量 Input 的值的不同,改变转速 speed、转向 Direction 等变量。 为实现对两个电机转速的分别调控,定义变量 channal,当按下按键“CH+”时,channa...
2、输入(INPUT)模式 3、输入上拉(INPUT_PULLUP)模式 (仅支持Arduino 1.0.1以后版本) 在输入上拉(INPUT_PULLUP)模式中,Arduino将开启引脚的内部上拉电阻,实现上拉输入功能。一旦将引脚设置为输入(INPUT)模式,Arduino内部上拉电阻将被禁用。 设置Arduino引脚为输出(OUTPUT)模式 当引脚设置为输出(OUTPUT)模式时,引脚...
begin(9600); // setup serial } void loop() { val = analogRead(analogPin); // read the input pin Serial.println(val); // debug value } RPI Pico的ADC是12Bits的,使用的参考电压是3.3V,所读的值对应的电压可以参照 公式voltage=3.3*value/4096 ...
// read the input on analog pin 0: int sensorValue =analogRead(A0); // Convert the analog reading (which goes from 0 - 1023) to a voltage (0 - 5V): float voltage = sensorValue * (5.0 / 1023.0); // print out the value you read: ...
void setup() { // initialize digital pin PC13 as an output. pinMode(PC13, OUTPUT);}// the loop function runs over and over again forevervoid loop() { digitalWrite(PC13, HIGH); // turn the LED on (HIGH is the voltage level) delay(1000); // wait for a second digital...
Serial.begin(9600); } // the loop routine runs over and over again forever: void loop() { // read the input on analog pin 0: float sensorValue = analogRead(A0); // convert ADC value to voltage float Vin = 5 * sensorValue / 1023; ...
Vin引脚供电(InputVoltage,一般接电池,连接到这个端口的电源需要稳压,否则非常容易损坏板子,我接过5V使用正常,有传说它和黑圆口是通着的)。 b. 数字端口:D0-D13,每个数字端口可以提供最高40mA电流和5V电压 c. PWM~:以~开头的数字端口,脉冲宽度调制,它是利用微处理器的数字输出来控制模拟电路的一种技术。最简单...