在看门狗(看门狗,又叫 watchdog timer,是一个定时器电路, 一般有一个输入,叫喂狗(kicking the dog or service the dog),一个输出到MCU的RST端,MCU正常工作的时候,每隔一端时间输出一个信号到喂狗端,给 WDT清零,如果超过规定的时间不喂狗,(一般在程序跑飞时),WDT 定时超过,就会给出一个复位信号到MC...
最新的 Arduino 1.5.6-r2 重新烧写mega2560的bootloader 烧写完之后 用usb直接编译下载 已经可以支持avr的这个wdt.h了,不用再像之前那样非得用ISP下载程序了。 使用代码如下: AI检测代码解析 /*--- avr看门狗测试 ---*/ #include <avr/wdt.h> void setup() { pinMode(13,OUTPUT); wdt_enable(WDTO_4S)...
TC-04 需要5V供电,但输出也是5V,ESP8266的各引脚只能接受3.3V的电压,所以需要接一个降压模块,或者是用电阻构建一个分压电路。 1、点动模式:按下遥控器继电器吸合,放开遥控器继电器断开; 2、自锁模式:按一下遥控器继电器吸合,再按一下遥控器则继电器断开; 3、互锁模式:手按遥控器第一个键,相应继电器接通,再按...
注意Arduino IDE 需安装 esp8266(By ESP8266 Community v3.0.2)库,操作步骤可参考CSDN-崔安兵-博客园(opens new window) 三、修改 Config.cpp 文件 修改设备标识和mqtt连接信息,如下图所示: 四、修改物模型数据 按照平台自定义物模型修改 User.cpp 文件,如下图所示: 注意串口观测到 wdt reset 时,可以在主程...
same sketch works fine in any Arduino board but not in esp8266 "NodeMCU" board. adding delay(1); solved my problem credit goes to@battosai30. Thanks!!! queenbey91 changed the title[-]NodeMCU wdt reset[/-][+] In case I can help someone, finally i found the explanation to this: :...
wdt reset Source Code : #include <ESP8266WiFi.h> #include <WiFiClientSecure.h> #include <TelegramBot.h> #define LED 14 //D3 const char* ssid = "Telegram"; const char* password = "getupdate"; const char BotToken[] = "660345429:ACGlSKhCRMmgKHNJH4pG3ut_1R_66flenqQ"; ...
ESP.wdtFeed( ) //喂狗 要是想复位 直接 ESP.restart()复位参考 ESP8266有两种重启方法,分别为:ESP.reset()和ESP.restart(),很多人代码中都用ESP.reset()重启,但是通常情况下使用ESP.restart()会更好, 这两者区别如下: ESP.reset()是一个硬复位,这种重启方式可能会使一些寄存器回归到原始状态,即丢失寄存器...
Re: Arduino esp8266 core files outdated [ESP EXCEPTION DECOD#71533 ByMcChubby007-Sat Nov 04, 2017 1:46 pm andre_teprom wrote:Hi there, I was tracing some wdt reset events by using theESP exception decodertool, and the first occurence were at theesp8266_wiring_digital.clocal file at ...
There are software and hardware watchdogs in ESP8266 Arduino core. The heavy crypto computing will lead to watchdog reset. There are disable/enable api of software-watchdog in ESP8266 Arduino core. I found theesp_hw_wdtto disable/enable the hardware-watchdog. ...
* @param cid 客户端id,如果是8266,可以设置为芯片id之类的,每个端都是独一无二 * @param user mqtt服务器账号 * @param pass mqtt服务器密码 */Adafruit_MQTT_Client(Client *client,constchar*server,uint16_tport,constchar*cid,constchar*user,constchar*pass): ...