5、在“Tools” 菜单中选择 Board 到“ESP32 Dev Module”。 6、在“Tools” 菜单中选择分区方案,”Default 4 4MB with fat (1.2MB APP/1.5MB FATFS)” 7、按 Arduino IDE 上传。 8、在“Tools” 菜单中选择 “ESP32 Sketch Data Upload”。 9、选择 FS 类型为 “FatFS”,然后按“确定”按钮。 PCB ...
如果更改为使用 SPIFFS 文件系统,则 esp32-nofrendo 示例已经在 data 文件夹中包含了一个 "Chase.nes" ROM 文件。 只需在 Arduino IDE 中选择 "工具" 菜单 -> "ESP32 Sketch Data Upload" 将 ROM 文件上传到 ESP32 SPIFFS。 你也可以将 ROM 文件复制到数据文件并上传。 注意: 此时,esp32-nofrendo 示例...
5)然后,要上传文件,请在Arduino IDE中,转到Tools > ESP32 Sketch Data Upload。 注意:在某些ESP32开发板上,您在上传文件时需要按住ESP32板上的“ BOOT ”按钮。当您看到“ Connecting…….___……”消息时,您需要按ESP32板载的“ BOOT ”按钮。 当您看到“ SPIFFS Image Uploaded ”消息时,文件已成功上传...
首先你需要一块ESP32开发板,本人使用的是一块ESP32-WROOM-32核心板,关于ESP32各个型号的区别可以进入乐鑫官网查看。 然后准备一块屏幕,我使用的是一块2.8寸(240*240)的tft屏幕,驱动是ST7789,使用spi通信协议。 二、软件准备 这里我使用的是vscode 的PlatformIO插件 新建文件,选择开发板为DOIT ESP32 DEVKIT V1,...
I use arduino IDE 2.3.2 for firmware but go back to 1.8.9 to use the ESP32 Sketch Data Upload Tool using spiffs. This works fine when using the IDE. But if I take the same spiffs file that is generated using the mkspiffs tool, use the webupdater.ino example, and use the Filesyst...
要上载程序前,先要用Arduino IDE连接ESP32板子,选择选择ESP32 Dev Kit。选择正确的串口。 然后,在Arduino IDE中选择File>Example>ArduinoOTA>OTAWebUpdate例子程序。在程序中更改成自己的WiFi名字和密码。 const char* ssid = "Your WiFi Name"; const char* password = "Password"; ...
It has always worked for me on "AVR ISP" although I'm unsure if it actually uses that over something else built in to the ESP32 board manager. Also make sure you put the ESP32 in programming mode when the Arduino IDE attempts to upload: Hold down "boot" button, and momentarily press...
Re: How to upload "data" to an ESP32 under Arduino 2.0 Postbychegewara»Tue Jun 08, 2021 11:38 am 1. command line tool 2. if you by any chance also using vs code with platformio then you can use it to flash spiffs/fatfs ...
Sketch voidsetup() { Serial.begin(115200); }voidloop() { ; } Debug Message Launching gdb-server: /Users/soodragon/Library/Arduino15/packages/esp32/tools/openocd-esp32/v0.12.0-esp32-20230921/bin/openocd -c "gdb_port 50000" -c "tcl_port 50001" -c "telnet_port 50002" -s /private/...
.pio\libdeps\esp32dev\TFT_eSPI\User_Setup.h 2.更改驱动配置 选择自己屏幕的驱动,并将其他驱动注释 选择显示的RGB顺序,并注释其他RGB顺序(如果不确定可以先选一个,之后看色彩不对再来更改) 选择屏幕显示屏的长和宽,并注释其他长宽 选择屏幕是否反转颜色(如果不确定可以先选一个如果颜色显示颠倒再来更改) ...