5) 附件:Arduino代码 /* Project: LED_Blink * Written by:Chris Marella * Date: January 4, 2017 * Description: The following code will flash an LED on and off. */ //Pin Definitions const int LED = 3; //define digital pin 3 as LED output void setup() { //Pin Configurations pinMode...
LED(bytep ,boolstate=LOW );//构造函数~LED();//析构函数bytegetPin();//获取控制的引脚voidon();//打开LEDvoidoff();//关闭LEDboolgetState();//获取LED状态voiddisattach();//释放引脚与LED的绑定,使得引脚可以控制其他的东西};#endif /*** LED.cpp ***/#include"LED.h"#include"Arduino.h"L...
#define _LED_H__//导入Arduino核心头文件#include"Arduino.h"classLED{private:byte pin;//控制led使用的引脚public:LED(byte p,bool state=LOW);//构造函数~LED();//析构函数bytegetPin();//获取控制的引脚voidon();//打开LEDvoidoff();//关闭LEDboolgetState();//获取LED状态voiddisattach();//释...
This project was put together by ScottC on the 15/01/2013http://arduinobasics.blogspot.com/Bluetooth slave code by Steve Chang - downloaded from :http://www.seeedstudio.com/wiki/index.php?title=Bluetooth_ShieldGrove Chainable RGB code can be found here :http://www.seeedstudio.com/wiki/Gro...
Turns on an LED on for one second,then off for one second,repeatedly. This example code is in the public do main. */ //Pin13 has an LED connected on most Arduino boards. //give it a name: Int led=13; //the setup routine runs once when you press reset ...
(ledPin,HIGH);// sets the LED onmyGizwits.setBindMode(WIFI_AIRLINK_MODE);//AirLink modebreak;default:break;}}voidsetup(){// put your setup code here, to run once:Serial.begin(9600);pinMode(ledPin,OUTPUT);// sets the digital pin as outputpinMode(myledPin,OUTPUT);// sets the ...
LED\ LED.ino 二、主文件代码框架规范 每一个Arduino程序(Sketch)都有1个主文件,后缀为.ino,它是程序的setup 函数和 loop函数所在的文件。 代码框架如下: void setup() { // put your setup code here, to run once: //初始化操作代码放在setup函数中,他们将在程序启动的第一步得到执行 并只执行一次 ...
(看图片)在右边,应该打开了Simulation View。您可以通过在右下方的模拟视图中单击单词 button 来模拟按钮按下事件。活动状态应从“熄灭”更改为“点亮”。五秒钟后,或单击时间事件 Light_On_timer_event_0 后,活动状态将更改回 Light Off 。太棒了!现在,让我们检查一下如何在Arduino上使用它。
/* Blink Turns on an LED on for one second, then off for one second, repeatedly. This example code is in the public domain. */ // Pin 13 has an LED connected on most Arduino boards. // give it a name: int led = 13; // the setup routine runs once when you press reset: void...
就让我们点亮第一颗LED灯~! 打开Raduino软件,按下图路径打开一个小程序。 这段程序非常简单: /* Blink Turns an LED on for one second, then off for one second, repeatedly. Most Arduinos have an on-board LED you can control. On the UNO, MEGA and ZERO it is attached to digital pin 13, ...