37款传感器与执行器的提法,在网络上广泛流传,其实Arduino能够兼容的传感器模块肯定是不止这37种的。鉴于本人手头积累了一些传感器和执行器模块,依照实践出真知(一定要动手做)的理念,以学习和交流为目的,这里准备逐一动手尝试系列实验,不管成功(程序走通)与否,都会记录下来—小小的进步或是搞不掂的问题,希望能够抛砖引...
1.首先打开如下路径的配置文件 .pio\libdeps\esp32dev\TFT_eSPI\User_Setup.h 2.更改驱动配置 选择自己屏幕的驱动,并将其他驱动注释 选择显示的RGB顺序,并注释其他RGB顺序(如果不确定可以先选一个,之后看色彩不对再来更改) 选择屏幕显示屏的长和宽,并注释其他长宽 选择屏幕是否反转颜色(如果不确定可以先选一个...
//#define TFT_D4 17 //#define TFT_D5 16 //#define TFT_D6 27 //#define TFT_D7 14 // ### EDIT THE PINs BELOW TO SUIT YOUR STM32 SPI TFT SETUP ### // The TFT can be connected to SPI port 1 or 2 //#define TFT_SPI_PORT 1 // SPI port 1 maximum clock rate is 55MHz...
我使用的是windows,我从微软商店安装了ArduinoIDE,但我想用VS Code编写所有代码。当我想运行程序或选择电路板时,它只显示以下内容: Cannot findArduinoIDE.Please specify the "arduino.path" in the user settings. Requires a restart after change.我如何解决这个问题,在哪里可以找到arduino.path?
On-board ST-LINK (STLINK/V2-1, STLINK-V3E, STLINK-V2EC, or STLINK-V3EC) debugger/programmer with USB re-enumeration capability: mass storage, Virtual COM port, and debug port Read moreRead less Featured Videos See All Getting started with ARM® mbed™ IDE ...
The document Si47XX ANTENNA, SCHEMATIC, LAYOUT, AND DESIGN GUIDELINES; AN383; rev 0.8; page 6; you will find the following note: "Crystal and digital audio mode cannot be used at the same time". So, for Digital Audio, you have to remove the crystal, and capacitors connected to the ...
Failed to open serial port /dev/cu.usbserial-11430 due to error: + Error: dlopen(/Users/user/.vscode-insiders/extensions/vsciot-vscode.vscode-arduino-0.4.2/out/node_modules/usb-detection/build/Release/detection.node, 1): no suitable image found. Did find: /Users/user/.vscode-insiders/exte...
In the bottom right corner, you should now see the name of your board, and the port it's connected to. Now click the right-pointing arrow in the top left corner to upload Blink to the board. You could also use the shortcut CTRL+U. ...
You can find them in.vscode/arduino.json under the workspace. { "sketch":"example.ino", "port":"COM5", "board":"adafruit:samd:adafruit_feather_m0", "output":"../build", "debugger":"jlink", "prebuild":"./", ...
This slowness is not a problem in many cases but if you do find it limiting, you can switch to flash breakpoints. When using flash breakpoints the watchdog cannot be used. Arduino library does not use watchdog so this is usually not a problem. If you need to use watchdog in your ...