/*Analog InputDemonstrates analog input by reading an analog sensor on analog pin 0 andturning on and off a light emittingdiode(LED) connected to digital pin 13.The amount of time the LED will be on and off depends on the value obtainedby analogRead().The circuit:- potentiometercenter pin ...
analogWrite(pin,Value) pin:3,5,6,9,10 ;在Arduino Mega2560中PWM口编号为2-13 Value: 设置输出的信号占空比,范围0-255 返回:None eg: 1 int ledPin=9; 2 int analogPin=3; 3 int val=0; 4 void setup() 5 { 6 pinMode(ledPin,OUTPUT); 7 } 8 void loop() 9 { 10 val=analogRead(analog...
pin:要设置其输出的引脚编号 value:HIGH(1),LOW(0) 返回值:无 模拟I/O 函数 Analog I/O Functions analogWrite(): 描述:在指定引脚输出指定占空比的 PWM 方波 函数原型:analogWrite(pin,value) 参数: pin:输出引脚 value:占空比,介于 0 - 255 之间 返回值:无 analogRead(): 描述:读取指定引脚的模拟信...
/*ButtonTurns on and off a light emitting diode(LED) connected to digital pin 13,when pressing a pushbutton attached to pin 2.The circuit:- LED attached from pin 13 to ground through 220 ohm resistor- pushbutton attached to pin 2 from +5V- 10K resistor attached to pin 2 from ground- ...
1.analogRead ( pin ) : ① 模拟输入引脚是带有ADC(Analog-to-Digital Converter,模数转换器)功能的引脚。 ②它可以将外部输入的模拟信号转换为芯片运算时可以识别的数字信号,从而实现读入模拟值的功能。 ③模拟输入功能需要使用analogRead() 函数。 参数:参数pin是指定要读取模拟值的引脚,被指定的引脚必须是模拟输入...
int button1State = 0; // variable for reading the pushbutton status int button2State = 0; // variable for reading the pushbutton status const int sensorPin = 0; // select the input pin for the potentiometer int sensorValue = 0; // variable to store the value coming from the sensor...
pinMode(A0,OUTPUT)...temp = analogRead(A0)想请问为什么将传感器输出口连接的A0设置为OUTPUT?这里不是用作数据输入吗,应该是INPUT把?不过我试了一下设置为OUTPUT和INPUT获取的数值差不多。是不是模拟口在没有Write过数据前设置IN/OUT没有差别呢?请问是什么原理。附上官网对于AnalogPin的一段话,也是要求在analog...
pinMode(buttonPin, INPUT);//定义buttonPin也就是前面定义的针脚3为input输入针脚 } void loop() { // ... } 1.2 loop() 在setup() 函数中初始化和定义了变量,然后执行 loop() 函数。顾名思义,该函数在程序运行过程中不断的循环,根据一些反馈,相应改变执行情况。通过该函数动态控制 Arduino 主控板。
#define button 4 int rotDirection = 0; int pressed = false; void setup() { pinMode(enA, OUTPUT); pinMode(in1, OUTPUT); pinMode(in2, OUTPUT); pinMode(button, INPUT); // Set initial rotation direction digitalWrite(in1, LOW); ...
pinMode(buttonPin, INPUT); } voidloop() { //… } 1.2 loop() 在setup() 函数中初始化和定义了变量,然后执行 loop() 函数。顾名思义,该函数在程 序运行 过程中不断的循环,根据一些反馈,相应改变执行情况。通过该函数动态控制 Arduino 主控板。