/*Blink without DelayTurns on and off a light emitting diode (LED) connected to a digital pin,without using the delay() function. This means that other code can run at thesame time without being interrupted by the LED code.The circuit:- Use the onboard LED.- Note: Most Arduinos have ...
打开和关闭连接到数字引脚的发光二极管(LED), 不使用Delay-()函数。这意味着其他代码可以运行在 同时没有被LED代码打断。 www.openmaker.cn */ /* Blink without Delay 不使用delay函数来使一个连接在数字口的LED闪烁,这意味着别的代码可以同时执行,而不会被LED的代码打断。 */ // 设置LED的引脚 const int ...
pinMode(ledPin, OUTPUT); } void loop() { // here is where you'd put code that needs to be running all the time. // check to see if it's time to blink the LED; that is, if the // difference between the current time and last time you blinked // the LED is bigger than th...
这看起来只是一种更复杂的闪烁LED的方式。然而,BinkWithoutDelay演示了一个非常重要的概念,称为状态机。 而不是依赖于delay()来计时闪烁。BlinkWithoutDelay会记住LED的当前状态以及它最后一次改变的时间。每次通过循环时,它都会查看millis()时钟,以确定是否再次更改LED的状态。 欢迎来到机器的世界 让我们来看看一个...
/*Blink without Delay 无延迟闪烁 Turns on and off a light emitting diode (LED) connected to a digital pin, without using the delay() function. This means that other code can run at the same time without being interrupted by the LED code. ...
这行代码使 LED_BUILTIN 引脚回到 0V,使 LED 熄灭。在点亮与熄灭之间,你会希望有足够的时间间隔,使人肉眼能看出点亮和熄灭的变化,delay() 命令就是让开发板在 1000毫秒(1秒)时间内停下来什么都不做。当你使用 delay() 命令,在你指定的延时时间内什么都不会发生。当你明白各个基本例子后,可以查看 BlinkWitho...
那是把pin13短接到0V,从而关闭LED灯。在LED灯开和关之间,你想要足够的时间来让人看到这个变化,所以delay()命令告诉开发板1000毫秒内什么都不做。当你用delay()命令,在这段时间里没有其他的事情发生。如果你明白这个基本例子,查看BlinkWithoutDelay的例子来学习当在做其他事时怎么制作一个延时 ...
https://www.arduino.cc/en/Tutorial/BuiltInExamples/BlinkWithoutDelay */ // constants won't change. Used here to set a pin number: const int ledPin = LED_BUILTIN;// the number of the LED pin // Variables will change: int ledState = LOW; // ledState used to set the LED ...
4. BlinkWithoutDelay: 这里的bilink借鉴的是examples中的BlinkWithoutDelay.ino中的blink方法,这种写法允许在blink的同时做其它工作。比如:读取按钮的输入等。但是如果使用的是Blink.ino中的写法,在delay()的时候是不能做其它工作的。 电路图: 完整源代码: ...
2.数字量 Digital Blink Without Delay:不使用延迟 delay() 功能使LED闪烁。 Button:使用按钮控制LED。 Debounce:读取一个按钮状态,过滤噪音。...3.模拟量 Analog Analog In Out Serial:读取模拟输入引脚,输出结果,然后使用该数据调暗或增亮LED。 Analog Input:使用电位计控制LED的闪烁。...5.控制结构 Contro...