LED灯:大多数Arduino板(如Arduino Uno)在数字引脚13上已经内置了一个LED灯,因此无需额外连接硬件。 如果需要连接外部LED灯,可以将LED的长脚(正极)连接到数字引脚13,短脚(负极)通过一个限流电阻(如220Ω)连接到GND。 运行结果 当代码上传到Arduino板并运行后,连接在数字引脚13上的LED灯会以每秒闪烁一次的频率不...
加载“Blink”例程 你可能会发现你的Arduino板的“L”LED已经在你连接USB插头的时候闪烁了。这是因为Arduino主板通常都是预先安装了“Blink”程序。 在这节课中,我们将用我们自己的Blink程序重新编程Arduino,然后改变它闪烁的速度。 在第0课中,你安装了Arduino IDE,并确保你能找到正确的串口来连接Arduino板。现在是...
Turns on an LED on for one second, then off for one second, repeatedly. This example code is in the public domain. */ 复制代码 这是代码中的说明文字,可以叫做注释。用"/*…*/",这个符号之间的内容将不被编译器编译。注释在代码中是非常有用的,它可以帮助你理解代码。IDE也将自动把注释的文字颜色...
2、闪烁 - Blink This example shows the simplest thing you can do with an Arduino to see physical output: it blinks the on-board LED. 本例展示了使用 Arduino 可以做的最简单的栗子查看物理输出:使板载 LED 闪烁 ~ (1)硬件需求 - Hardware Required Arduino Board optional 可选 LED 220 ohm resisto...
原文地址 - https://www.arduino.cc/en/Tutorial/Blink 闪烁 这个例子展示了你能拿 Arduino / Genuino 板子来干的最简单的事:使开发板上的 LED 灯闪烁。 硬件需求 Arduino 开发板 LED (非必要) 220欧电阻(非必要) 电路 这
This example code is in the public domain. http://www.arduino.cc/en/Tutorial/BlinkWithoutDelay */ // constants won't change. Used here to set a pin number : const int ledPin = 13; // the number of the LED pin // Variables will change : ...
This example code is in the public domain. http://www.arduino.cc/en/Tutorial/Blink */ // the setup function runs once when you press reset or power the board void setup() { // initialize digital pin LED_BUILTIN as an output.
This example code is in the public domain. https://www.arduino.cc/en/Tutorial/BuiltInExamples/BlinkWithoutDelay */ // constants won't change. Used here to set a pin number: const int ledPin = LED_BUILTIN;// the number of the LED pin ...
Arduino Code This code is used to blink an LED connected with pin number 22 with a delay of one second. void setup() { pinMode(22, OUTPUT); // Set GPIO22 as digital output pin } void loop() { digitalWrite(22, HIGH); // Set GPIO22 active high ...
Blink*/// 在大多数Arduino控制板上 13号引脚都连接了一个标有“L”的LED灯// 我们给13号引脚设置一个别名“led”int led = 13;//在板子启动或者复位重启后, setup部分的程序只会运行一次void setup(){ // 将“led”引脚设置为输出状态 pinMode(led, OUTPUT);}//setup部分程序运行完后,loop部分的程序...