Writes an analog value (PWM wave) to a pin. Can be used to light a LED at varying brightnesses or drive a motor at various speeds. After a call to analogWrite(), the pin will generate a steady square wave of the specified duty cycle until the next call to analogWrite() (or a cal...
analogWrite(analogOutPin, outputValue); // print the results to the serial monitor: Serial.print("sensor = "); Serial.print(sensorValue); Serial.print("\t output = "); Serial.println(outputValue); // wait 2 milliseconds before the next loop // for the analog-to-digital converter to s...
/*Mega analogWrite() testThis sketch fades LEDs up and down one at a time on digital pins 2 through 13.This sketch was written for the Arduino Mega, and will not work on other boards.The circuit:- LEDs attached from pins 2 through 13 to ground.created 8 Feb 2009by Tom IgoeThis examp...
模拟输入功能需要使用analogRead(pin)函数,其中pin是读取模拟值的引脚,被指定的引脚必须是模拟输入引脚。 1.2 模拟输出功能 要使用analogWrite()函数来实现模拟输出功能。 注意: 该函数并不是输出真正意义上的模拟值,而是以一种特殊的方式来达到输出模拟值的效果,也就是我们经常听到的“...
pinMode() analogRead() digitalWrite() delay() AnalogInOutSerial - 读取一个模拟输入引脚,按比例划分读数,然后用这个数据来熄灭或者点亮一个LED灯 AnalogWriteMega - 用一个Arduino或者Genuino Mega开发板来使12个LED灯一个接一个逐渐打开和熄灭 Calibration - 定义期望中的模拟传感值的最大值和最小值 ...
analogRead(pin) 参数:[A0-A5];返回值:[0-1023] analogWrite(pin, value) 参数:[3,5,6,9,10,11],[0-255];返回值:无 说明:PWM wave 490Hz 高级I/O pulseIn(pin, value, [timeout]) 参数:[n],[HIGH | LOW],{unsigned long}(微秒;默认:1 秒); ...
(ledPin, OUTPUT); //数字口要选择带~号的具有pwm功能的输出口 } void loop() { readValue = analogRead(A0); //读取A0模拟口的数值(0-5V 对应 0-1204取值) ledValue = map(readValue, 0, 1024, 0, 255); //将0到1024之间的数据映射成0到255之间的数据 analogWrite(ledPin, ledValue); //PWM最...
首先是analogWrite()函数,该函数定义数字I/O引脚的PWM“电压电平”(有关PWM和analogWrite()的更多信息)。在这种情况下,这就是LED亮度(LOB)的级别。然后剩下的loop()函数就是改变亮度的算法。这应该是不言自明的。如果没有,让我们快速进行一下。在第32行上,我们向当前LOB添加一个阶跃值,然后询问LOB是否小于或...
pin:要读取的模拟引脚的编号 返回值:无 在analogWrite() 和 analogRead() 函数内部,已经完成了引脚的初始化,因此不用在 Setup() 函数中进行初始化操作。 数学函数 Math Functions map(): 描述:将数字从一个范围重新映射到另一个范围。 函数原型:map(value, fromLow, fromHigh, toLow, toHigh) 参数: val...
{ pinMode(ledPin, OUTPUT); //数字口要选择带~号的具有pwm功能的输出口 } void loop(){ readValue = analogRead(A0); //读取A0模拟口的数值(0-5V 对应 0-1204取值) ledValue = map(readValue, 0, 1024, 0, 255); // 将0到1024之间的数据映射成0到255之间的数据 analogWrite(ledPin, ledValue);...