/*Analog InputDemonstrates analog input by reading an analog sensor on analog pin 0 andturning on and off a light emittingdiode(LED) connected to digital pin 13.The amount of time the LED will be on and off depends on the value obtainedby analogRead().The circuit:- potentiometercenter pin ...
/*ButtonTurns on and off a light emitting diode(LED) connected to digital pin 13,when pressing a pushbutton attached to pin 2.The circuit:- LED attached from pin 13 to ground through 220 ohm resistor- pushbutton attached to pin 2 from +5V- 10K resistor attached to pin 2 from ground- ...
1.analogRead ( pin ) : ① 模拟输入引脚是带有ADC(Analog-to-Digital Converter,模数转换器)功能的引脚。 ②它可以将外部输入的模拟信号转换为芯片运算时可以识别的数字信号,从而实现读入模拟值的功能。 ③模拟输入功能需要使用analogRead() 函数。 参数:参数pin是指定要读取模拟值的引脚,被指定的引脚必须是模拟输入...
const int button1Pin = 2; // the number of the pushbutton1 pin const int button2Pin = 4; // the number of the pushbutton2 pin const int relay1Pin = 7; // the number of the Realy1 pin const int relay2Pin = 8; // the number of the Relay2 pin const int sensorPin = 0; ...
pin:要设置其输出的引脚编号 value:HIGH(1),LOW(0) 返回值:无 模拟I/O 函数 Analog I/O Functions analogWrite(): 描述:在指定引脚输出指定占空比的 PWM 方波 函数原型:analogWrite(pin,value) 参数: pin:输出引脚 value:占空比,介于 0 - 255 之间 返回值:无 analogRead(): 描述:读取指定引脚的模拟信...
Serial.begin(9600);//设置波特率pinMode(13,OUTPUT);//设置某个引脚是输出还是输入} loop()//每个arduino程序中必须包含的连续执行函数,setup()初始化后的执行函数,相当于C语言中的main()voidloop() {if(digitalRead(buttonPin)==HIGH) serialWrite('H');elseserialWrite('L'); ...
#define button 4 int rotDirection = 0; int pressed = false; void setup() { pinMode(enA, OUTPUT); pinMode(in1, OUTPUT); pinMode(in2, OUTPUT); pinMode(button, INPUT); // Set initial rotation direction digitalWrite(in1, LOW); ...
pinMode(A0,OUTPUT)...temp = analogRead(A0)想请问为什么将传感器输出口连接的A0设置为OUTPUT?这里不是用作数据输入吗,应该是INPUT把?不过我试了一下设置为OUTPUT和INPUT获取的数值差不多。是不是模拟口在没有Write过数据前设置IN/OUT没有差别呢?请问是什么原理。附上官网对于AnalogPin的一段话,也是要求在analog...
– 20-pin header (J5)Camera – 20-pin Arducam camera header (J6)USB1x USB Type-C port for programming and HID1x USB 2.0 host Type-A portAudio – 3.5mm audio jackI/OsUp to 76x I/O pins (including the camera/display headers)4x UART, 3x I2C, 2x SPI12x PWMUp to 12x analog ...
All 6 analog input pins are available. They can also be used as digital pins (pins #14 thru 19) Digital pin 2, and 13 are not used. The following pins are in use only if the DC/Stepper noted is in use:Digital pin 11: DC Motor #1 / Stepper #1 (activation/speed control)Digital ...