2个12bit ADC合计12路通道，其中10个外部通道：PA0-PA7、PB0-PB1，2个内部通道：温度传感器通道ADC_Channel_16和内部参考电压通道ADC_Channel_17。测试代码示例：void setup(){ Serial.begin(115200); pinMode(PA0, INPUT_ANALOG);}void loop(){ delay(50); Serial.print("PA0="); Serial.pri...
ADC0-ADC5 其实是作为 PC0-PC5 的第二功能存在的,分别对应 Arduino 定义 A0-A5。也正因为次,在 Arduino 的官方指南中提到,“The analog input pins can be used as digital pins, referred to as A0, A1, etc. ”。说的是,模拟输入口可以当数字口一样用。对于A0-A5来说,确实不错。但对于第一功能就...
int analogPin = 3;//使用analog in 引脚3 作为电压标记 int val = 0; // 读取到的电压值 void setup() { Serial.begin(9600); //串口传输波特率 1s传输的字节 } void loop() { val = analogRead(analogPin); // 读取输入的电压值 Serial.println(val); // 串口输出返回值 } 1. 2. 3. 4. ...
//Declare A5Analogpin as input pin pinMode(A5, INPUT); //Declare4-13 Digital Pins as Output Pins (For controlling 10 x ROHM LEDs) pinMode(4, OUTPUT); pinMode(5, OUTPUT); pinMode(6, OUTPUT); pinMode(7, OUTPUT); pinMode(8, OUTPUT); pinMode(9, OUTPUT); pinMode(10, OUTPUT); ...
int ledPin = 9; // LED connected to digital pin 9 int analogPin = 3; // potentiometer connected to analog pin 3 int val = 0; // variable to store the read value void setup() { pinMode(ledPin, OUTPUT); // sets the pin as output } void loop() { val = analogRead(analogPin)...
pinMode() analogRead() digitalWrite() delay() AnalogInOutSerial - 读取一个模拟输入引脚,按比例划分读数,然后用这个数据来熄灭或者点亮一个LED灯 AnalogWriteMega - 用一个Arduino或者Genuino Mega开发板来使12个LED灯一个接一个逐渐打开和熄灭 Calibration - 定义期望中的模拟传感值的最大值和最小值 ...
int ledPin = 9; // LED connected to digital pin 9 int analogPin = 3; // potentiometer connected to analog pin 3 int val = 0; // variable to store the read value void setup() { pinMode(ledPin, OUTPUT); // sets the pin as output ...
格瑞图:Arduino-0007-内置示例-读取模拟电压 Read Analog Voltage 格瑞图:Arduino-0008-内置示例-非延迟闪烁 Blink Without Delay 格瑞图:Arduino-0009-内置示例-按钮 Button 格瑞图:Arduino-0010-内置示例-去抖 Debounce 格瑞图:Arduino-0011-内置示例-数字输入上拉 DigitalInputPullup ...
The analogWrite function has nothing whatsoever to do with the analog pins or the analogRead function.这个analogWrite⽅法与模拟引脚或者analogRead⽅法毫不相⼲ Syntax 语法 analogWrite(pin, value)Parameters 参数 pin: the pin to write to.pin：输出的引脚号 value: the duty cycle: between 0 (...
// Servo control digital output pins defined as global constants const int controlPin3A = 6; const int controlPin4A = 8; const int servoENablePin = 3; // Motor control global variables: int motorSpeed = 0; // Motor speed 0..255 ...