DHT sensor library Description An Arduino library for the DHT series of low-cost temperature/humidity sensors. You can find DHT tutorialshere. Dependencies Adafruit Unified Sensor Driver Contributing Contributions are welcome! Not only you’ll encourage the development of the library, but you’ll also...
将Adafruit-Fingerprint-Sensor-Library-master文件夹重命名为Adafruit_Fingerprint_Sensor_Library文件夹; 将文件夹移动到您的Arduino IDE安装库文件夹; 最后,重新打开Arduino IDE。 Arduino实验开源代码之三 /* 【Arduino】168种传感器模块系列实验(资料代码+仿真编程+图形编程) 实验一百四十一:AS608光学指纹识别模块 智...
将Adafruit-Fingerprint-Sensor-Library-master文件夹重命名为Adafruit_Fingerprint_Sensor_Library文件夹; 将文件夹移动到您的Arduino IDE安装库文件夹; 最后,重新打开Arduino IDE。 Arduino实验开源代码之三 /* 【Arduino】168种传感器模块系列实验(资料代码+仿真编程+图形编程) 实验一百四十一:AS608光学指纹识别模块 智...
library.properties Update library.properties - bump version to 2.1.3 Jan 31, 2024 license.txt basic info Mar 20, 2012 Repository files navigation README License Adafruit-Fingerprint-Sensor-Library Secure your project with biometrics - this all-in-one optical fingerprint sensor will make adding finge...
安装库:IDE—工具—管理库—搜索Adafruit-Fingerprint-Sensor-Library—安装 实验接线: Vi +3.3V(请勿接3.3V以上电源,否则烧毁模块!) TX 2 RX 3 GND GND */ #include <Adafruit_Fingerprint.h> // On Leonardo/Micro or others with hardware serial, use those! #0 is green wire, #1 is white ...
安装库:IDE—工具—管理库—搜索Adafruit-Fingerprint-Sensor-Library—安装 实验接线: Vi +3.3V(请勿接3.3V以上电源,否则烧毁模块!) TX 2 RX 3 GND GND */ #include <Adafruit_Fingerprint.h> // On Leonardo/Micro or others with hardware serial, use those! #0 is green wire, #1 is white ...
1.在Arduino IDE中,转到File > Examples > Adafruit Fingerprint Sensor Library > Fingerprint,然后将代码上传到Arduino开发板。 2.以9600的波特率打开串行监视器。您应该会看到以下消息: 3.在扫描仪中放置要识别的手指。 4.在串行监视器上,您可以看到与指纹匹配的ID。同时它也显示了信心值 – 信心值越高,表示该...
安装库:IDE—工具—管理库—搜索Adafruit-Fingerprint-Sensor-Library—安装 实验接线: Vi +3.3V(请勿接3.3V以上电源,否则烧毁模块!) TX 2 RX 3 GND GND */#include<Adafruit_Fingerprint.h>// On Leonardo/Micro or others with hardware serial, use those! #0 is green wire, #1 is white// uncomment ...
安装库:打开IDE—工具—管理库—搜索DHT—安装"DHT sensor library" 项目测试:读取DHT11的串口输出数据 模块接线: DHT11 Arduino VCC 5V GND GND DATA D2 */ #include <Adafruit_Sensor.h> #include <DHT.h> #include <DHT_U.h> #define DHTPIN 2 ...
要使用DH11需要先下载DH11的函数库,打开Arduino后,管理库,在搜索 DH11 即可搜索到 DHT_sensor_library。 打开示例 DHTtester ,编译上传,会发现一个错误,大致意思是缺少 Adafruit_Sensor.h 这个头文件,可在https://github.com/adafruit/Adafruit_Sensor此处下载。