1、2.2.1双V槽专用下模座安装在下部台面上,下部台面的夹板上紧。Amada折弯机操作说明本操作规程规定了数控折弯机的操作方法及参数设定、工艺要求、使用安全注意事项及日常维护与保养。适用于本公司 AMADA 数控折弯机的操作。2、操作方法、操作方法2.1开机2.1.1操作容:钥匙插入电源ON/OFF开关,转到ON位置动作状况:电源...
通过AMADA的V槽模具解决方案,除了无需配置专机,起到降低成本的效果外,还能够实现加工效率的提升。以图13样品为例,以往的加工仅在刨槽机上就需要2min4s,而采用V槽模具后仅需要1min14s(4刀),刨槽本身就节约了将近一半时间,如果再计算材料搬运、重定位等时间的话,效率的提升将更为显著。 图13 对SUS304 实测板厚...
TOOL CHANGE开关打向为关(刀具更换) RAM POSITION开关(冲头定位) RAM SPEED ff关(冲头速度) 十一、清除机器周围的一切物体。 十二、按START键执行程序。控制面板上的AUTO OPERATION灯亮。显示器上的光标按程序块向下跳动。 十三、程序结束,控制面板上的AUTO OPERATION灯熄灭,桌而和货物返回,控制而板上的+X,+Y灯...
PRESS SELECTION 开关(压力选择) SINGLE 键(单冲) TEST 键(程序检测) TOOL CHANGE 开关打向为关(刀具更换) RAM POSITION 开关(冲头定位) RAM SPEED 开关(冲头速度) 十一﹑清除机器周围的一切物体。 十二﹑按 START 键执行程序。控制面板上的 AUTO OPERATION 灯亮。显示器上的光标按程序块向下跳动。 十三﹑程序...
2: V-width (V-opening) of tool used for bending (V) 3: Required tonnage to bend 1m long material (F)[ Right figure, symbol of tonnage chart ] V=V-width (V-opening) b=Minimum flange length ir=Inner bend radius t=Material thickness (Tensile...
≒V/6 Base values for maintaining safe and stable accuracy, such as punch tip radius and spring-back amount. Partial Bending When high accuracy is required, use a bottoming type tool. Coining Care must be taken when using a bottoming die because iR increases and extra...
It greatly affects machine specifications, tool selection, product accuracy and quality, so let's grasp the contents and use them for safe work. First of all, read the following contents from the chart below.1: Minimum flange length (b) 2: ...
PRESS SELECTION 开关(压力选择) SINGLE 键(单冲) TEST 键(程序检测) TOOL CHANGE 开关打向为关(刀具更换) RAM POSITION 开关(冲头定位) RAM SPEED 开关(冲头速度) 十一﹑清除机器周围的一切物体。 十二﹑按 START 键执行程序。控制面板上的 AUTO OPERATION 灯亮。显示器上的光标按程序块向下跳动。 十三﹑程序...
≒V/6 Base values for maintaining safe and stable accuracy, such as punch tip radius and spring-back amount. Partial Bending When high accuracy is required, use a bottoming type tool. Coining Care must be taken when using a bottoming die because...
所谓ARFT,就是AMADA Rapid Forming Tool的首字母简写,即:AMADA高速成形模具。这是一种针对如图1所示的产品生产中,利用AMADA高速数控冲床的冲压上模和下模夹紧材料,并通过轴移动进行成形加工的一种加工工艺(图2)。 图1 利用高速成形加工的样品 图2 ARFT加工原理及过程示意图 ...