7. 将所有层的 Undefined line width 设成 0.1524 8. 将所有层的 shape bounding box 设成 2.54 9. 将 GND 和 VCC层设置成负片,Plot mode 的 Negative 选中 10. 将最下端的输出参数 Vector based pad behavior 选中 11. 将 General Parameters 的参数照图 3.20设置一下 12. 点击 OK 按钮关闭 Artwork Co...
Undefined linewidth:5mil 或者0.125mm Shape boundingbox:100mil 或者2.5mm Plot mode:各层的正片还是负片的格式,将会从板子的叠层的设置中读出,并设置到光绘中。 选项“Deletesignal layer unconnected pads” 当这个选项选中的时候,电气层的内层的信号层在层的属性为正片的情况下,Suppressunconnected pads打勾 选项...
5.Shape bounding box : 輸入100 ﹐表示當Plot Mode 為Negative時﹐由Shape 的邊緣往外畫100 mil黑色區域。 6.Plot mode : 點選Positive , 表示采用正片的畫出格式。 7.Film mirrored : 不勾選此項﹐表示不將底片做左右反轉。 8.Film contact thermal-reliefs : 不勾選此項﹐只有當Plot Mode 為Negative時...
选中层叠结构中的每一层,都设置为6mil --》 [Shape bounding box] 选中层叠结构中的每一层,都设置为100 --》 [plot mode] 选中层叠结构中的每一层,无特殊情况都选择Positive --》 [Vector based pad behavior] 选中每一层都勾选上 点击OK完成参数设置 (2) 生成光绘文件,Manufacture--》 Artwork 仔细检查...
选择输出单位,这里选择毫米;其他选择默认。film control ;undefined line width选择0.2,注意保证每次的该选项都为0.2,不能为空否则将出错;shape bounding box 选择2.54,;在check database befor artwok前打勾。下面添加gerber层。 4.一般默认的available films 只有top和bottom;注意默认的是大写,需要改为小写。将鼠标...
--》 [Shape bounding box] 选中层叠结构中的每一层,都设置为100 --》 [plot mode] 选中层叠结构中的每一层,无特殊情况都选择Positive --》 [Vector based pad behavior] 选中每一层都勾选上 点击OK完成参数设置 (2) 生成光绘文件,Manufacture--》 Artwork ...
--> [Film options] --> [Undefined line width] 选中层叠结构中的每一层,都设置为6mil --> [Shape bounding box] 选中层叠结构中的每一层,都设置为100 --> [plot mode] 选中层叠结构中的每一层,无特殊情况都选择Positive --> [Vector based pad behavior] 选中每一层都勾选上 点击OK完成参数设置 ...
BOARD GEUMETRY/DIMCj drill-1-2亡| drill-5-6 drill2-5Create ArtworkFilm optionsFilm name:silk-bottomRotation:|0 jdIOffset X:|0.0000Y:10.0000Undefined line width:10.1000Shape bounding box: 12.5400Plot mode:& Positive广 NegativeV Film mirroredFull contact thermal-reliefs厂 Suppress unconnected pads...
4.此时通过show element (i)可显示该shape信息 也可通过Edit/Z-Copy复制, 在copy to class/ subclass中选择board geometry及outline后,框选outline0125板框即可 步骤三:加载零件 设置封装库路径 1.导入零件前首先确认已建好该项目的封装库, 2.再在Allegro中设置封装库路径 Setup-User Preferences (paths中Library中...
--> [Shape bounding box] 选中层叠结构中的每一层,都设置为100 --> [plot mode] 选中层叠结构中的每一层,无特殊情况都选择Positive --> [Vector based pad behavior]选中每一层都勾选上 点击OK完成参数设置 (2) 生成光绘文件,Manufacture--> Artwork ...