Alpas, Elevated temperature wear of Al6061 and Al6061-20%Al2O3, Scr. Metall. Mater. 32 (1995) 1099-1105, http://dx.doi.org/10.1016/0956- 716X(94)00004-2.J. Singh, A.T. Alpas, Elevated temperature wear of Al 6061 and Al6061-Al2O3, Scripta Metallurgica et Materialia 32 (7)...
Maximum use temperature in air ( C ) 130 - 150 Melting point ( C ) 585.00 Specific heat ( J K⁻1 kg⁻1 ) 878.0 - 914.0 Thermal conductivity ( W m⁻1 K⁻1 ) 152.00 - 169.00 Mechanical Properties(机械性能) Elongation at break ( % ) 12.0 -25.0 Tensile strength ( MPa ) 124....
In this work, high temperature wear of A16061 and A16061-20%Al{sub 2}O{sub 3} was studied at temperatures between 25--500 C. The microstructural changes that occurred during wear have been delineated in order to understand the wear mechanisms that operate at high temperatures. 展开 ...
MaterialData_AL 6061 T6 Tensile Strength, Ultimate Tensile Strength, Yield
6xxx (6061: Al-0.9Mg-0.7Si-0.3Cu-0.3Fe-0.1Ti) L-PBF (with heated build plate at 500 °C) 318 290 5.4 [82] 7xxx (7075: Al-5.5Zn-2.5Mg-1.6Cu-0.4Si-0.3Fe-0.2Cu-0.2Ti) L-PBF with Grain refiner + T6 383–417 325–373 3.8–5.4 [73] Empty Cell 7xxx (Al-7A77: Al-5.5...
Process development in stir casting and investigation on microstructures and wear behavior of TiB2 on Al6061 MMC. Proc Eng. 2013;64:1183–90. Article CAS Google Scholar Yashpal, Sumankant, Jawalkar CS, Verma AS, Suri NM. Fabrication of aluminium metal matrix composites with particulate ...
aAnD.d1o7Zo1nr,Bg2,21Ji.3nL–-.s2iHt2u1igc(ho1m9st9rp3ao)i.nsitreast.eJ.teAnlsloilyespCroompeprdti.e6s6o3f,a7n55(A–7162O8 3(2p0a1r6ti)c.les)-(Al alloy 6061-T6) metal matrix 12. Poletti, C. et al. High-temperature strength of compacted sub-micrometer aluminium powder....
SWEET等人[8]发现在6061铝合金中,随着Fe含量的增加,富铁相由针状β-Al5FeSi转变为汉字状αc-AlFeSi。林波等人[9]发现挤压铸造Al-Cu合金中随着Fe含量的增加,针状富铁相增加,Al-Cu合金的常温性能和高温性能急剧下降。吴广新等人[10]研究了Mn元素对热浸镀Al10Si2Fe合金镀层显微组织的影响,发现随着Mn含量的增加,...
Fig. 3. Summary of cross-sectional OM images showing the Al-Si-Zn coating layers deposited on Al 6061 substrate. Furthermore, the wettability between the casting alloy and coating layers was examined by pouring molten alloy onto the coated substrate. However, most of the substrate and cast Al...
The effect of repeated thermal cycling is of particular concern for aluminum alloys, which have relatively low melting temperatures. Here, a laser-hotwire directed energy deposition AM system was used to deposit aluminum alloy 4043 wire (Al-Si alloy) onto an Al 6061-T6 billet (Al-Si-Mg alloy...