AGMA 2000--A88-中文翻译版本.pdf,AGMA 2000--A88 March 1988 1988年3月 (Errata 1992) (勘误表1992年) (PartialRevision ofAGMA 390.03) (对AGMA 390.03进行部分修正) - CAUTION- - 注意- While this document is the current published AGMA Standard on this subj ec
> ANSI-AGMA 2000-A88 下载文档 收藏 打印 转格式 2031阅读文档大小:11.75M158页shinningtree上传于2012-11-22格式:PDF ANSI-AGMA 2005-D03锥齿轮设计手册 热度: ANSI-AGMA_2004-B89 热度: [机械/仪表]ANSI-AGMA 2001-D04 热度: ReturntoMenu ReturntoMenu ...
1~ 2- 2001 和AGMA2000- A88 齿轮精度标准中的精度等级、 检验组、 偏差的计算公式和公差表格、齿廓偏差和螺旋线偏差进行了简 要的分析探讨, 给出 了两标准部分偏差项目 的精度等级对应关系 。关键词 精度等级 检验组 齿廓偏差 螺旋线偏差 对照 引言2001 年我国颁布了 GB/T10095. 1 - 2001 和 GB/T10095...
本 文结合 ISO 1328 标 准和 A GMA 2000- A 88 标 准对 比分析 了最新 美 国齿轮标准 A NSI/ A GMA 2015,为大家了解美国最新的齿轮标准提供一定 的参考。 关键词 : IS O1 328 AG MA 2000一 A88 A NS I/ A G MA 201 5 齿轮 标准前言 随着市场 国际化 和采购全球化 的不 断深 入, 每个...
AGMA+ISO+14179-1.pdf69 ANSI+AGMA+1003-G93+(R1999).pdf68 ANSI+AGMA+1006-A97+(R2003).pdf68 ANSI+AGMA+1010-E95+(R2004).pdf96 ANSI+AGMA+1012-2005.pdf82 ANSI+AGMA+1102-A03.pdf82 ANSI+AGMA+1106-A97+(R2003).pdf62 ANSI+AGMA+2000-A88.pdf140 ...
AGMA-2015-1-A01-2001.pdf阅读:1762次|页数:44页|上传:2012-02-17 17:12 A N S I / A G M A 2 0 1 5 - 1 - A 0 1 ANSI/AGMA2015-1-A01 (Replaces ANSI/AGMA2000--A88) AMERICANNATIONALSTANDARD AccuracyClassificationSystem- TangentialMeasurementsforCylindrical Gears ii AccuracyClassification...
ANSI/AGMA1006-A97(R2003)ANSI/AGMA1010-E95(R2004)ANSI/AGMA1012-2005ANSI/AGMA1102-A03 ANSI/AGMA1106-A97(R2003)ANSI/AGMA2000-A88ANSI/AGMA2001-D04 ANSI/AGMA2002-B88(R1996)ANSI/AGMA2003-B97(R2003)ANSI/AGMA2004-B89(R2006)ANSI/AGMA2005-D03ANSI/AGMA2007-C00 ANSI/AGMA2008-C01ANSI/AGMA2009-...
Both of these documents, when com- bined, officially replace the still widely used standard, AGMA 2000-A88: Gear Classification and Inspection Handbook.Although ANSI/AGMA 2015-2-A06 was adopted by the general membership, it is likely that most members--even to this day--do not fully ...
《AGMA-2001-D04-2004.pdf》由会员分享,可在线阅读,更多相关《AGMA-2001-D04-2004.pdf(66页珍藏版)》请在人人文库网上搜索。 ansi/agma2001-d04 ansi/agma 2001-d04 (revision of ansi/agma 2001-c95) american national standard fundamental rating factors and calculation methods for involute spur and hel...
AGMA 915--1--A02, Inspection Practices - Part 1: Cylindrical Gears - Tangential Measurements AGMA 2000--A88, Gear Classification and Inspection Handbook - Tolerances and Measuring Methods for Unassembled Spur and Helical Gears (Including Metric Equivalents) ANSI/AGMA 2002--B88, Tooth Thickness ...