2. Short-Circuit Constraint (Allowed=No) (All),(All) 短路约束,即禁止不同网络的电气相接触。 设置如下图示: 3. Un-Routed Net Constraint ( (All) ) 未布线的网络,即没有连线的网络或者断开的某条线。 设置图示: 4. Modified Polygon (Allow modified: No), (Allow shelved: No) 多边形覆铜调整未...
2.Short-Circuit Constraint (Allowed=No) (All),(All) 短路约束=不允许)(全部),(全部) 3.Un-Routed Net Constraint ( (All) ) 26 Un-Routed净约束(所有)26 4.Clearance Constraint (Gap=9mil) (All),(All) 间隙约束(间隙= 9 mil)(全部),(全部) 5.Power Plane Connect Rule(Relief Connect )(Exp...
2.Short-Circuit Constraint (Allowed=No) (All),(All) 短路约束=不允许)(全部),(全部) 3.Un-Routed Net Constraint ( (All) ) 26 Un-Routed净约束(所有)26 4.Clearance Constraint (Gap=9mil) (All),(All) 间隙约束(间隙= 9 mil)(全部),(全部) 5.Power Plane Connect Rule(Relief Connect )(Exp...
AD设计规则检查.doc,Rule Violations Count 违反数 Short-Circuit Constraint (Allowed=No) (All),(All) 短路约束=不允许)(全部),(全部) Un-Routed Net Constraint ( (All) ) 26 Un-Routed净约束(所有)26 Clearance Constraint (Gap=9mil) (All),(All) 间隙约束(间隙= 9 mil
layout完成后,需要对PCB进行规则检查,选择Tools--Quick Reports,依次检查shape Dynamic state,Unconnect Pins Report,Design ruler Check(DRC) Report。 2019-08-21 08:40:17 板子在布线之前执行规则检查,出现Un-Routed Net Constraint错误 这几天一直准备着一个STM32的板子,今天终于布局弄好了,我就便执行了规则检...
12Un-RoutedNetConstraint有线路未连接检查未连接的走线,将其连上 13Short-CircuitConstraint短路约束 14ClearanceConstraint间隙约束 AD6.9电气规则检查报错说明 元器件超过Room界线 有线路独立存在于Room中,未删除或者未连接 按D、R将规则中的SilkscreenOverComponentPads改 小一些就可以了 你的某个元件的焊盘间距大于1...
规则检查出现Un-R..线都连上了啊,应该怎么改动呢?回复 醉沓Hum :你把你工程发给我吧回复 醉沓Hum :你看看焊盘的网络名和你线的网络名一样吗?
Other graphics, including those used to represent violations of Net Antennae, Short-Circuit, Un-Routed Net, Room Definition, Layer Pairs and Vias Under SMD rules, will simply be a graphic, as there is no definable constraint value to be displayed. ...
2.Short-Circuit Constraint (Allowed=No) (All),(All) 短路约束=不允许)(全部),(全部) 3.Un-Routed Net Constraint ( (All) ) 26 Un-Routed净约束(所有)26 4.Clearance Constraint (Gap=9mil) (All),(All) 间隙约束(间隙= 9 mil)(全部),(全部) 5.Power Plane Connect Rule(Relief Connect )(Exp...