重新导入ifcfg-eth0网络配置文件 [root@localhost ~]# /etc/init.d/network reload Shutting down interface eth0: [ OK ] Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface eth0: [ OK ] 网卡接口关闭与激活 [root@localhost ~]# ifdown eth0 ...
如下: #route del default dev eth0 //删掉刚才配的静态路由 #route add default gw 192.168.1.1 //写默认路由的下一跳地址 现在ping外网却通了! [root@localhost ~]# netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 ...
删除IP地址:使用ip addr del<IP>/<MASK> dev <INTERFACE>可以从接口上删除IP地址。 启用/禁用接口:使用ip link set <INTERFACE> up/down可以启用或禁用网络接口。 示例代码 代码语言:txt 复制 # 查看所有网络接口信息 ip add show # 为eth0接口添加IP地址 ip addr add 192.168.1.100/24 dev eth0 # 从eth...
Thedevoption specifies that the traffic should be sent out theeth0interface. Example 2 Let's say that you have two routers: Router 1: IP address 10.0.0.1/24 Router 2: IP address 192.168.1.1/24 And you want to add a route to the 10.10.10.0/24 network on Router 1 that should be sen...
查看指定接口所属区域: firewall-cmd --get-zone-of-interface=eth0 拒绝所有包:firewall-cmd --panic-on 取消拒绝状态: firewall-cmd --panic-off 查看是否拒绝: firewall-cmd --query-panic 那怎么开启一个端口呢 添加 firewall-cmd --zone=public --add-port=80/tcp --permanent (--permanent永久生效...
在某些Linux发行版中,可以通过修改grub配置文件来禁用Predictable Network Interface Names功能,从而恢复传统的eth0、eth1等命名方式。这通常涉及编辑/etc/default/grub文件,设置GRUB_CMDLINE_LINUX变量以包含net.ifnames=0 biosdevname=0选项,然后重新生成grub配置文件并重启系统。例如: bash sudo sed -i 's/GRUB_CMDL...
这是一条Linux系统IP地址配置命令。具体含义是：设置系统的IP地址为192.168.0.2；子网掩码为24，也就是255.255.255.0；广播地址为192.168.0.255；网卡设备名称为eth0。网络中的计算机都必须设置唯一的IP地址，才能正常通信。由于有这种唯一的地址，才保证了用户在联网的计算机上操作时，能够高效而且...
1、win+R打开资源管理器输入:cmd点击:确定，在cmd里面输入:route/?来查看route命令和参数的使用。2、查看本地所有路由信息:routeprint。3、强制使用IPv4进行查看:routeprint-4。4、强制使用IPv6进行查看:routeprint-6。5、查看指定路由信息:routeprint127*。6、添加路由信息:routeadd158.0.0.0mask255...
Multipass needs to create a bridge to connect to eth0. This will temporarily disrupt connectivity on that interface. Do you want to continue (yes/no)? On Linux, Multipass requiresNetworkManagerto achieve this. On installations that do not haveNetworkManagerinstalled (e.g. Ubuntu Server), the us...
Apart from the default route, you can also configure additional routes. For example, your server you might have 2 interfaces (eth0 and eth1). By default, all the traffic is routed through interface eth0 irrespective of what IP address you have configured