2. 问题 : 为什么CubeMX ADC clock 无法选择 Synchronous /1 or /2 模式 可以看到如下图,我们在设定 STM32G474 MCU 的 ADC 周边,当要设定 Clock Prescaler 时,却无法选择 Synchronous clock mode divided by 1 ( 同步模式除1 ) 或是 Synchronous clock mode di
GPIO_InitTypeDef GPIO_InitStructure; RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC |RCC_APB2Periph_ADC1 , ENABLE ); RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE ); GPIO_InitStructure.GPIO_Pin=GPIO_Pin_1; GPIO_InitStructure.GPIO_Mode=GPIO_Mode_AIN; GPIO_Init(GPIOC,&GPIO_InitStructure); ...
Aiming at different application, MCU products of CHENGXIN is divided into general purpose MCU and special purpose MCU. General purpose MCU is used in consumer electronics products, household appliances and intelligent controller,which has IO type series
2. 問題 : 為什麼CubeMX ADC clock 無法選擇 Synchronous /1 or /2 模式 可以看到如下圖,我們在設定 STM32G474 MCU 的 ADC 周邊,當要設定 Clock Prescaler 時,卻無法選擇 Synchronous clock mode divided by 1 ( 同步模式除1 ) 或是 Synchronous clock mode divided by 2 ( 同步模式除2 )。 3. 說明...
应该是系统时钟分频作为ADC的时钟
AD9708 在时钟(CLOCK)的驱动下工作,内部集成了+1.2V 参考电压(+1.20V REF)、运算放大器、电流源(CURRENT SOURCE ARRAY)和锁存器(LATCHES)。两个电流输出端 IOUTA 和 IOUTB 为一对差分电流,当输入数据为 0(DB7~DB0)时,IOUTA 的输出电流为 0,而 IOUTB 的输出电流达到最大,最大值的大小跟参考电压有关...
START是开始转换信号;EOC是转换结束信号;CLOCK是时钟,因为判断是一步一步进行的 VREF+和VREF-是 DAC的参考电压,比如0-4095是对应0-3.3V还是0-5V,就看参考电压。 DAC的参考电压也是ADC外设的输入范围。 VCC和GND就是芯片供电;通常VREF+和VCC接在一起, VREF-和GND接在一起。
voidAdcConfig(void){/* enable ADC clock */rcu_periph_clock_enable(RCU_ADC);/* config ADC clock */rcu_adc_clock_config(RCU_ADCCK_APB2_DIV6);adc_resolution_config(ADC_RESOLUTION_12B);/* ADC data alignment config */adc_data_alignment_config(ADC_DATAALIGN_RIGHT);/* ADC channel length co...
ADC模块的时钟(ADCCLK)通常由APB2总线时钟分频而来。具体分频系数可通过寄存器或库函数配置,需确保ADCCLK不超过芯片允许的最大值(例如STM32F1系列最大为14MHz,其他系列如F4/H7可能更高,需查数据手册)。 2.配置ADC时钟步骤 a.使能ADC时钟 标准库:通过RCC_APB2PeriphClockCmd()开启ADC模块的时钟。
Clock Jitter Will Have a Spectrum Too In the introduction, we established the relationship between the signal, the overall voltage noise, and the rms of clock jitter. The SNR figure connects those three in a fairly straightforward Equation 2. The SNR figure is a good benchmark to compare circ...