TX_MON inputs are DC biased and C1 capacitor is an AC coupling capacitor used to AC couple TX_MON input. R2 is a damping resistor to minimize series resonance comprised of on chip inductance and capacitance....
//tx1_mon_lo_cm *** adi,txmon-1-lo-cm48, //tx2_mon_lo_cm *** adi,txmon-2-lo-...
文件页数/大小:74 页 / 1778 K 品牌: ADI [ ADI ] AD9361 参数1 符号 最小值 典型值 最大值 件 测试条件/注释 TX监控器输入(TX_MON1, TX_MON2) 最大输入电平 4 66 1 dBm dB dB 动态范围 准确度 LO频率合成器 LO频率阶跃 2.4 Hz
AD9361发射单频信号接收到的信号存在明显的谐波 使用AD9361芯片发射单频信号,AD_CLK = 983.08M,1Tx,D/A速率为30.72M,使用FMC-COMMS3开发板接收,采用LTE20M的配置,关闭了开发板自身的发射信号。分别测试 苏州光格 2018-09-04 10:27:48 请问监控AD9361输出功率要怎么做 TX_MON可以用于发射功率监控,请问如果要...
TX_MON inputs require a matching/attenuation network to provide matching to the driving source typically a 50Ω coupler output and to scale the input signal. Matching components R1‐R3 and C1 should be placed as close as possible to the AD9361. ...
REG_MULTICHIP_SYNC_AND_TX_MON_CTRL, MCS_RF_ENABLE); REG_MULTICHIP_SYNC_AND_TX_MON_CTRL, MCS_RF_ENABLE);dev_dbg(&phy->spi->dev, "%s : %s state %d", __func__, tx ? "TX" : "RX", enable); dev_dbg(&phy->spi->dev, "%s : %s state %d", __func__, tx ? "TX" : ...
ad9361帖子 1 0 请问如果用AD9361制作发射机引脚CTRL,GPO,TX_MON,FB_CLK,DATA_CLK是不是就不用接? 标签:引脚AD936128681 1 0 请问AD9361中CLK_OUT引脚的作用是什么? 标签:引脚AD936146651 2 0 大家用AD9361做什么 标签:AD936156862 3 0 AD9361TDD模式下RX和TX的切换进入不了TX状态...
AD9361_datasheet
(DC Offset tracking) 11 0x035 = 0x16 (Gain Control) 12 0x035 = 0x17 (Gain Control) 12 0x035 = 0x18 (DC Offset Tracking, Power Word Ready) 12 0x035 = 0x19 (Charge Pump Calibration States) 12 0x035 = 0x1A (Rx VCO and ALC Calibration States) 12 0x035 = 0x1B (Tx VCO and ...
(Tx VCO and ALC Calibration States) 12 0x035 = 0x1C (Rx VCO Calibration States) 13 0x035 = 0x1D (Rx VCO Calibration States) 13 0x035 = 0x1E (Gain Control, Temp Sense Valid, AuxADC Valid) 13 0x035 = 0x1F (Gain Control) 13 Page 2 of 13 ADI Confidential AD936x Control Output...