ACS712和各种Arduino开发板的连接都很简单,VCC连接于Arduino开发板的5V引脚,GND与GND连接,OUT引脚连接于A0引脚。 首先,要从 (File > Examples > Basics) 上传AnalogReadSerial sketch 文件到Arduino。如果没有电流,使用的是10bit ADC时串口监视器的显示值为一半(512 -2.5V)。如下将来自传感器的电压值转换为电流读数...
Arduino AC DC 30A 电流传感器 ACS712ELC-30A 说明书Arduino Current Sensor AC/DC 30A Model: ACS712ELC-30A User Manual Schematic Diagram: Interface: Measurement:©2022 Baidu |由 百度智能云 提供计算服务 | 使用百度前必读 | 文库协议 | 网站地图 | 百度营销 ...
您好,欢迎来到另一个教程,这个是关于测量交流电 (AC),使用ACS712我使用的是 30Amps 版本,即 ACS712 30A,以及我们可爱的 Arduino Uno 板,我尝试添加一个 OLED 屏幕但不幸的是结束了在拍摄教程时打破了它,所以我切换到 LCD,但在下面你会找到两个版本的接线和代码。 “任何交流电……”我的意思是我们将看到一个...
Connecting the ACS712 Module to an Arduino is very simple. We just need to connect VCC of the Module to the 5V pin of the Arduino (red wire), and GND of the Module to the GND pin of the Arduino (black wire). Finally, we need to connect the Sensor output (OUT) to the analog in...
The module's ease of use and compatibility with the Arduino platform make it an excellent choice for those looking to add precise current measurement capabilities to their projects. Data download: https://pan.baidu.com/s/1OhDjf-3tQgJFQL0h4WY5sw 1. Current sensor chip: ACS712ELC-30A; 2....
The module's design is optimized for use with Arduino, making it a seamless addition to any project. Its small size and lightweight nature make it easy to integrate into various setups, from portable devices to fixed installations. **Versatile Application Scenarios** The ACS712 module is not...
您好,欢迎来到另一个教程,这个是关于测量交流电 (AC),使用ACS712我使用的是 30Amps 版本,即 ACS712 30A,以及我们可爱的 Arduino Uno 板,我尝试添加一个 OLED 屏幕但不幸的是结束了在拍摄教程时打破了它,所以我切换到 LCD,但在下面你会找到两个版本的接线和代码。 “任何交流电……”我的意思是我们将看到一个...
acs712电流传感器是基于霍尔效应来测量电流的,使用起来其实挺简单的。首先,你需要把传感器接到电流回路上,它就能通过霍尔效应产生电压差,这个电压差和电流是成比例的。然后,你可以用像Arduino或者STM32这样的开发板来读取这个电压值,再通过一些计算就能得到电流值了。不同的量程对应不同的换算关系,所以要根据自己购买的...
用Arduino读取ACS712电流传感器的输出 电流传感器(Current Sensor)用途广泛,如电源、过流保护、马达控制等。本项目将通过Arduino开发板,演示如何用ACS712传感器模组进行电压读数。项目BOM如下: AA电池 2022-07-27 08:32:23 如何使用ACS712进行电源/能量测量?
ACS712(uint8_t analogPin, float volts = 5.0, uint16_t maxADC = 1023, float mVperAmpere = 100)constructor. It defaults a 20 A type sensor, which is defined by the default value of mVperAmpere. See table below. Volts is the voltage used by the (Arduino) internal ADC. maxADC is ...