Router#conf t Enter configuration commands,one per line.EndwithCNTL/Z.Router(config)#hR1R1(config)#int f0/0R1(config-if)#ip add10.0.1.2255.255.255.0R1(config-if)#no shutR1(config-if)#int s1/0R1(config-if)#ip add
Two types of IP ACL can be configured in Cisco Packet Tracer 8.2 : Standard ACLs: This is the oldest ACL type which can be configured on Cisco routers. Traffic is filtered based on the source IP address of IP packets. The access-list number can be any number from 1 to 99. This kind...
Cisco Packet Tracer 方法/步骤 1 实验拓扑图：2 配置设备ip及网关路由器ip配置： Router>enableRouter#conf terEnter configuration commands, one per line. End with CNTL/Z.Router(config)#int f0/0Router(config-if)#ip add 192.168.1.1 255.255.255.0Router(config-if)#no shutRouter(config-if)#ex...
1 使用Cisco Packet Tracer6.3 2 实验使用拓扑 3 首先先查看许可文件情况enableshow license feature 4 需要激活2911路由器设备的许可操作步骤如下：Router>enableRouter#configure terminal Router(config)#license boot module c2900 technology-package securityk9PLEASE READ THE FOLLOWING TERMS CAREFULLY. INSTALLING T...
1.新建Packet Tracer拓扑图 2.路由器之间通过V.35电缆通过串口连接,DCE端连接在R1上,配置其时钟频率64000;主机与路由器通过交叉线连接。 3.配置路由器接口IP地址。 4.在路由器上配置动态路由协议,让三台PC能够相互Ping通,因为只有在互通的前提下才涉及到方控制列表。
Enter configuration commands, one per line. End with CNTL/Z. yangyu-R0(config)#int fa 0/0 /配置FA0/0 端口 yangyu-R0(config-if)#ip add 192.168.2.1 255.255.255.0 yangyu-R0(config-if)#no shut /启用该端口 yangyu-R0(config-if)#int s 1/0 /配置serial1/0 端口 ...
(config-if)#no shutR3:Router>Router>enRouter#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#h R3R3(config)#int s1/0R3(config-if)#ip add 10.0.2.2 255.255.255.0R3(config-if)#no shutR3(config-if)#int f0/0R3(config-if)#ip add 8.8.8.1 255.255.255.0...
packettracer建构实验攻略15acl简单配置.pdf,PacketTracer5.3建构CCNA实验攻略(15)——ACL简单的配置 Packet Tracer 5.3是一款非常不错的Cisco(思科)网络设备模拟器,对于想考思科初级认 证(如CCNA)的朋友们来说,PacketTracer5.3是非常不错的选择。通常我们周围并没有 那
username senya password 0 cisco ! ip ssh version 1 no ip domain-lookup ! ! interface FastEthernet0/0 no ip address duplex auto speed auto shutdown ! interface FastEthernet0/1 ip address 192.168.3.1 255.255.255.0 duplex auto speed auto ...
ciscoasa# packet-tracer input outside tcp 10.0.50.50 1234 10.105.130.27 443 !--- NAT untranslate from10.105.130.27/443 to 172.30.0.10/443 Phase: 1 Type: UN-NAT Subtype: static Result: ALLOW Config: object network web-server nat (dmz,outside) static 10.105.130.27 ...